Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
An essential component of a noise-free audio device isa clean power supply, but few switching regulators canoperate at high efficiency while keeping the switchingfrequency out of the audio band. The LTC®3620 fills thisvoid. It is a high efficiency 15mA buck regulator with aprogrammable minimum switching frequency, making itpossible to virtually eliminate audible switching noise. Theinternal synchronous switches and low quiescent currentof this buck regulator provide the ability to maintain highefficiency, while its small footprint makes it ideal for tiny,low power audio applications.
上传时间： 2013-10-21
上传用户：非衣2016
Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上传时间： 2013-10-25
上传用户：brain kung
A recent trend in the design of portable devices has beento use ceramic capacitors to filter DC/DC converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上传时间： 2013-11-05
上传用户：comer1123
Photomultipliers (PMT), avalanche photodiodes (APD),ultrasonic transducers, capacitance microphones, radiationdetectors and similar devices require high voltage,low current bias. Additionally, the high voltage must bepristinely free of noise; well under a millivolt is a commonrequirement with a few hundred microvolts sometimesnecessary. Normally, switching regulator confi gurationscannot achieve this performance level without employingspecial techniques. One aid to achieving low noise is thatload currents rarely exceed 5mA. This freedom permitsoutput fi ltering methods that are usually impractical
上传时间： 2013-10-28
上传用户：lhw888
In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (see separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
上传时间： 2013-10-30
上传用户：yeling1919
Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
标签： Switchin Output Single SKS
上传时间： 2013-10-30
上传用户：taa123456
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
上传时间： 2013-10-12
上传用户：司令部正军级
