Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上传时间： 2013-11-08
上传用户：xianglee
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Alkaline batteries are convenient because they’re easy tofi nd and relatively inexpensive, making them the powersource of choice for portable instruments and devicesused for outdoor recreation. Their long shelf life alsomakes them an excellent choice for emergency equipmentthat may see infrequent use but must be ready to go on amoment’s notice. It is important that the DC/DC convertersin portable devices operate over the widest possiblebattery voltage range to extend battery run time, and thussave the user from frequent battery replacement.
上传时间： 2014-12-24
上传用户：569342831
Automotive power systems are unforgiving electronicenvironments. Transients to 90V can occur when thenominal voltage range is 10V to 15V (ISO7637), along withbattery reversal in some cases. It’s fairly straightforwardto build automotive electronics around this system, butincreasingly end users want to operate portable electronics,such as GPS systems or music/video players,and to charge their Li-Ion batteries from the automotivebattery. To do so requires a compact, robust, effi cientand easy-to-design charging system
上传时间： 2013-11-04
上传用户：wfl_yy
Many system designers need an easy way to producea negative 3.3V power supply. In systems that alreadyhave a transformer, one option is to swap out the existingtransformer with one that has an additional secondarywinding. The problem with this solution is that manysystems now use transformers that are standard, offthe-shelf components, and most designers want toavoid replacing a standard, qualifi ed transformer with acustom version. An easier alternative is to produce thelow negative voltage rail by stepping down an existingnegative rail. For example, if the system already employsan off-the-shelf transformer with two secondary windingsto produce ±12V, and a –3.3V rail is needed, a negativebuck converter can produce the –3.3V output from the–12V rail.
上传时间： 2013-10-09
上传用户：Jerry_Chow
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-21
上传用户：baitouyu
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
