波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2013-10-10
上传用户：zxc23456789
【摘要】本文结合作者多年的印制板设计经验，着重印制板的电气性能，从印制板稳定性、可靠性方面，来讨论多层印制板设计的基本要求。【关键词】印制电路板；表面贴装器件；高密度互连；通孔【Key words】Printed Circuit Board；Surface Mounting Device；High Density Interface；Via一．概述印制板（PCB－Printed Circuit Board）也叫印制电路板、印刷电路板。多层印制板，就是指两层以上的印制板，它是由几层绝缘基板上的连接导线和装配焊接电子元件用的焊盘组成，既具有导通各层线路，又具有相互间绝缘的作用。随着SMT（表面安装技术）的不断发展，以及新一代SMD（表面安装器件）的不断推出，如QFP、QFN、CSP、BGA（特别是MBGA），使电子产品更加智能化、小型化，因而推动了PCB工业技术的重大改革和进步。自1991年IBM公司首先成功开发出高密度多层板（SLC）以来，各国各大集团也相继开发出各种各样的高密度互连（HDI）微孔板。这些加工技术的迅猛发展，促使了PCB的设计已逐渐向多层、高密度布线的方向发展。多层印制板以其设计灵活、稳定可靠的电气性能和优越的经济性能，现已广泛应用于电子产品的生产制造中。下面，作者以多年设计印制板的经验，着重印制板的电气性能，结合工艺要求，从印制板稳定性、可靠性方面，来谈谈多层制板设计的基本要领。
上传时间： 2013-10-08
上传用户：zhishenglu
讨论、研究高性能覆铜板对它所用的环氧树脂的性能要求，应是立足整个产业链的角度去观察、分析。特别应从HDI多层板发展对高性能CCL有哪些主要性能需求上着手研究。HDI多层板有哪些发展特点，它的发展趋势如何——这都是我们所要研究的高性能CCL发展趋势和重点的基本依据。而HDI多层板的技术发展，又是由它的应用市场——终端电子产品的发展所驱动（见图1）。 图1 在HDI多层板产业链中各类产品对下游产品的性能需求关系图 1．HDI多层板发展特点对高性能覆铜板技术进步的影响1.1 HDI多层板的问世，对传统PCB技术及其基板材料技术是一个严峻挑战20世纪90年代初，出现新一代高密度互连（High Density Interconnection，简称为 HDI）印制电路板——积层法多层板（Build—Up Multiplayer printed board，简称为 BUM）的最早开发成果。它的问世是全世界几十年的印制电路板技术发展历程中的重大事件。积层法多层板即HDI多层板，至今仍是发展HDI的PCB的最好、最普遍的产品形式。在HDI多层板之上，将最新PCB尖端技术体现得淋漓尽致。HDI多层板产品结构具有三大突出的特征：“微孔、细线、薄层化”。其中“微孔”是它的结构特点中核心与灵魂。因此，现又将这类HDI多层板称作为“微孔板”。HDI多层板已经历了十几年的发展历程，但它在技术上仍充满着朝气蓬勃的活力，在市场上仍有着前程广阔的空间。
上传时间： 2013-11-19
上传用户：zczc
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-16
上传用户：萍水相逢
a8259 可编程中断控制 altera提供 The a8259 is designed to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 interrupts, and in the cascade mode, this can be expanded up to 64 interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
上传时间： 2015-01-02
上传用户：panpanpan
为了提高直接转矩控制（DTC）系统定子磁链估计精度，降低电流、电压测量的随机误差，提出了一种基于扩展卡尔曼滤波（EKF）实现异步电机转子位置和速度估计的方法。扩展卡尔曼滤波器是建立在基于旋转坐标系下由定子电流、电压、转子转速和其它电机参量所构成的电机模型上，将定子电流、定子磁链、转速和转子角位置作为状态变量，定子电压为输入变量，定子电流为输出变量，通过对磁链和转速的闭环控制提高定子磁链的估计精度，实现了异步电机的无速度传感器直接转矩控制策略，仿真结果验证了该方法的可行性,提高了直接转矩的控制性能。 Abstract: In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results show it is efficient and improves the control performance.
上传时间： 2015-01-02
上传用户：qingdou
Logger iButton devices have gained a lot of popularity with researchers. Although free evaluation software is easy to use and welldocumented, the choices and inputs that need to be made can sometimes be challenging. This application note explains technicalterms that are common with temperature logger iButtons and how they relate to each other. Additionally, it presents an algorithm tohelp users choose the necessary input parameters, including the sample rate based on a user's needs and the available memory tostore the data.
上传时间： 2013-11-16
上传用户：xywhw1
Semiconductor memory, card readers, microprocessors,disc drives, piezoelectric devices and digitally based systemsfurnish transient loads that a voltage regulator mustservice. Ideally, regulator output is invariant during a loadtransient. In practice, some variation is encountered andbecomes problematic if allowable operating voltage tolerancesare exceeded. This mandates testing the regulatorand its associated support components to verify desiredperformance under transient loading conditions. Variousmethods are employable to generate transient loads, allowingobservation of regulator response
上传时间： 2013-11-21
上传用户：semi1981
基于通用集成运算放大器，利用MASON公式设计了一个多功能二阶通用滤波器，能同时或分别实现低通、高通和带通滤波，也能设计成一个正交振荡器。电路的极点频率和品质因数能够独立、精确地调节。电路使用4个集成运放、2个电容和11个电阻，所有集成运放的反相端虚地。利用计算机仿真电路的通用滤波功能、极点频率和品质因数的独立控制和正交正弦振荡，从而证明该滤波器正确有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
上传时间： 2013-10-09
上传用户：13788529953
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
