BC20-TE-B NB-Iot 评估板评估板原厂原理图V1.2。完整对应实物装置。
上传时间： 2022-06-17
上传用户：
ASR M08-B设置软件 V3.2 arduino 2560+ASRM08-B测试程序 arduino UNO+ASRM08-B测试程序语音控制台灯电路图及C51源码(不带校验码) 继电器模块设置。 ASR M08-B是一款语音识别模块。首先对模块添加一些关键字，对着该模块说出关键字，串口会返回三位的数，如果是返回特定的三位数字，还会引起ASR M08-B的相关引脚电平的变化。【测试】①打开“ASR M08-B设置软件 V3.2.exe”。②选择“串口号”、“打开串口”、点选“十六进制显示”。③将USB转串口模块连接到语音识别模块上。接线方法如下：语音模块TXD --> USB模块RXD语音模块RXD --> USB模块TXD语音模块GND --> USB模块GND语音模块3V3 --> USB模块3V3（此端为3.3V电源供电端。）④将模块的开关拨到“A”端，最好再按一次上面的大按钮（按一次即可，为了确保模块工作在正确的模式）。⑤对着模块说“开灯”、“关灯”模块会返回“0B”、“0A”，表示正常(注意：0B对应返回值010，0B对应返回值010，返回是16进制显示的嘛，设置的时候是10进制设置的)。
标签： ASR M08-B
上传时间： 2022-07-06
上传用户：aben
心音信号是人体最重要的生理信号之一，包含心脏各个部分如心房、心室、大血管、心血管及各个瓣膜功能状态的大量生理病理信息。心音信号分析与识别是了解心脏和血管状态的一种不可缺少的手段。本文针对目前该研究领域中存在的分析方法问题和分类识别技术难点展开了深入的研究，内容涉及心音构成的分析、心音信号特征向量的提取、正常心音信号（NM）和房颤（AF）、主动脉回流（AR）、主动脉狭窄（AS）、二尖瓣回流（MR）4种心脏杂音信号的分类识别。本文的工作内容包括以下5个方面： a）心音信号采集与预处理。本文采用自行研制的带有录音机功能的听诊器实现对心音信号的采集。通过对心音信号噪声分析，选用小波降噪作为心音信号的滤波方法。根据实验分析，选择Donoho阈值函数结合多级阈值的方法作为心音信号预处理方案。 b）心音信号时频分析方法。文中采用5种时频分析方法分别对心音信号进行了时频谱特性分析，结果表明：不同的时频分析方法与待分析心音信号的特性有密切关系，即需要在小的交叉项干扰与高的时频分辨率之间作综合的考虑。鉴于此，本文提出了一种自适应锥形核时频（ATF）分析方法，通过实验验证该分布能较好地反映心音信号的时频结构，其性能优于一般锥形核分布（CKD）以及Choi-Williams分布（CWD）、谱图（SPEC）等固定核时频分析方法，从而选择自应锥形核时频分析方法进行心音信号分析。 c）心音信号特征向量提取。根据对3M Littmann（） Stethoscopes[31]数据库中标准心音信号的时频分析结果，提取8组特征数据，通过Fihser降维处理方法提取出了实现分类可视化，且最易于分类的心音信号的2维特征向量，作为心音信号分类的特征向量。 d）心音信号分类方法。根据心音信号特征向量组成的散点图，研究了支持向量机核函数、多分类支持向量机的选取方法，同时，基于分类的目的 性和可信性，本文提出以分类精度最大为判断准则的核函数参数与松弛变量的优化方法，建立了心音信号分类的支持向量机模型，选取标准数据库中NM、AF、AR、AS、MR每类心音信号的80组2维特征向量中每类60组数据作为支持向量机的学习样本，对余下的每类20组数据进行测试，得到每类的分类精度（Ar）均为100％，同时对临床上采集的与上述4种同类心脏杂音信号和正常心音信号中每类24个心动周期进行分类实测，分类精度分别为：NM、AF、MR的分类精度均为100％，而AR、AS均为95．83％，验证了该方法的分类有效性。 e）心音信号分析与识别的软件系统。本文以MATLAB语言的可视化功能实现了心音信号分析与识别的软件运行平台构建，可完成对心音信号的读取、预处理，绘制时-频、能量特性的三维图及两维等高线图；同时，利用MATLAB与EXCEL的动态链接，实现对心音信号分析数据的存储以及统计功能；最后，通过对心音信号2维特征向量的分析，实现心音信号的自动识别功能。 本文的研究特色主要体现在心音信号特征向量提取的方法以及多分类支持向量机模型的建立两方面。 综上所述，本文从理论与实践两方面对心音信号进行了深入的研究，主要是采用自适应锥形核时频分析方法提取心音信号特征向量，根据心音信号特征向量组成的散点图，建立心音信号分类的支持向量机模型，并对正常心音信号和4种心脏杂音信号进行了分类研究，取得了较为满意的分类结果，但由于用于分类的心脏杂音信号种类及数据量尚不足，因此，今后的工作重点是采集更多种类的心脏杂音信号，进一步提高心音信号分类精度，使本文研究成果能最终应用于临床心脏量化听诊。 关键词：心音信号，小波降噪，非平稳信号，心脏杂音，信号处理，时频分析，自适应，支持向量机
上传时间： 2013-04-24
上传用户：weixiao99
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
This document describes part number speciÞc changes to recommended operating conditions and revised electrical speciÞcations,as applicable, from those described in the generalMPC7400 Hardware SpeciÞcations.SpeciÞcations provided in this Part Number SpeciÞcation supersede those in theMPC7400 Hardware SpeciÞcationsdated 9/99(order #: MPC7400EC/D) for these part numbers only; speciÞcations not addressed herein are unchanged. This document isfrequently updated, refer to the website at http://www.mot.com/SPS/PowerPC/ for the latest version.Note that headings and table numbers in this data sheet are not consecutively numbered. They are intended to correspond to theheading or table affected in the general hardware speciÞcation.Part numbers addressed in this document are listed in Table A. For more detailed ordering information see Table B.
上传时间： 2013-11-19
上传用户：qiaoyue
USB Manager(usbmgr) 0.4.8 Shuu Yamaguchi <shuu@wondernetworkresources.com> Special Helper: Philipp Thomas When USB devices connect to or disconnect from a USB hub, the usbmgr works as the following according to configuration. a) It loads and unloads files Linux kernel modules. b) It execute file to setup USB devices.
标签： wondernetworkresources Yamaguchi Manager Special
上传时间： 2014-01-27
上传用户：zhaiyanzhong
Description: FASBIR(Filtered Attribute Subspace based Bagging with Injected Randomness) is a variant of Bagging algorithm, whose purpose is to improve accuracy of local learners, such as kNN, through multi-model perturbing ensemble. Reference: Z.-H. Zhou and Y. Yu. Ensembling local learners through multimodal perturbation. IEEE Transactions on Systems, Man, and Cybernetics - Part B: Cybernetics, 2005, vol.35, no.4, pp.725-735.
标签： Description Randomness Attribute Filtered
上传时间： 2015-04-10
上传用户：ynzfm
mp3设计程序资料，采用c语言编写。 README file for yampp-3 source code 2001-05-27 This is the current state of the yampp-3 source code, 2001-05-27. This code is intended to run on Rev. B of the yampp-3 PCB, but can ofcourse be used on compatible systems as well. It still uses the "old" song selection system as the yampp-2. However, the disk handling routines has improved a lot and the obviosly, the new VS1001 handling has been put in. The codesize is almost at it s maximum at 1F40 bytes. A .ROM file is included if you don t have the compiler set up. For now, the documentation is in the code
上传时间： 2015-04-13
上传用户：小码农lz
prolog 找路例子程序： === === === === === === Part 1-Adding connections Part 2-Simple Path example | ?- path1(a,b,P,T). will produce the response: T = 15 P = [a,b] ? Part 3 - Non-repeating path As an example, the query: ?- path2(a,h,P,T). will succeed and may produce the bindings: P = [a,depot,b,d,e,f,h] T = 155 Part 4 - Generating a path below a cost threshold As an example, the query: ?- path_below_cost(a,[a,b,c,d,e,f,g,h],RS,300). returns: RS = [a,b,depot,c,d,e,g,f,h] ? RS = [a,c,depot,b,d,e,g,f,h] ? no ==================================
标签： Part connections example prolog
上传时间： 2015-04-24
上传用户：ljt101007
