AT89S52-24单片机最小系统开发板ALTIUM设计硬件原理图+PCB文件,2层板设计，大小为121x149mm，Altium Designer 设计的工程文件，包括完整的原理图及PCB文件，可以用Altium(AD)软件打开或修改，可作为你的产品设计的参考。主要器件型号列表如下：Library Component Count : 14Name Description----------------------------------------------------------------------------------------------------AT89S52-P 8 位微处理器/40引脚CAP CapacitorCAPACITOR POL CapacitorCRYSTAL CrystalD Connector 9 Receptacle Assembly, 9 Position, Right AngleHeader 2 Header, 2-PinHeader 4 Header, 4-PinHeader 5X2 Header, 5-Pin, Dual rowLED MAX232PZ_9 排针——9RES2SW-DPST Double-Pole, Single-Throw SwitchSW-PB Switch
上传时间： 2021-11-17
上传用户：
AT89S52单片机主8入8出继电器工控主板ALTIUM设计硬件原理图+PCB文件,2层板设计，大小为121x149mm，Altium Designer 设计的工程文件，包括完整的原理图及PCB文件，可以用Altium(AD)软件打开或修改，可作为你的产品设计的参考。主要器件型号列表如下：Library Component Count : 25Name Description----------------------------------------------------------------------------------------------------24LC02AJKG 按键开关AT89S52-P 8 位微处理器/40引脚CAP CapacitorCAPACITOR POL CapacitorCPDR 瓷片电容CRYSTAL CrystalD Connector 9 Receptacle Assembly, 9 Position, Right AngleDG 电感DJDR 电解电容GO 光耦Header 5X2 Header, 5-Pin, Dual rowJDQYCK 继电器——1常开1常闭LED 发光二极管LM2576HVT-3.3 Simple Switcher 3A Step Down Voltage RegulatorMAX232 NPN NPN Bipolar TransistorPZ_2 排针——2PZ_3 排针——3RES2Res 电阻Res PZ_8 8位排阻SW-DPST Double-Pole, Single-Throw SwitchWY2JG 稳压二级管ZL2JG 整流二极管
上传时间： 2021-11-17
上传用户：kingwide
一份极好PCB的EMC设计指南 这是一份关闭PCB方面EMC的一些讲解，里面对应PCB设计讲得比较详细，对于从事PCB设计相关的人，可以学习一下。
标签： emc
上传时间： 2022-01-28
上传用户：
以STC12C5A60S2单片机为控制核心,采用2.4G(JF24D)无线遥控模块进行无线发射与接收,设计了一种双电机遥控船模控制系统.该系统通过切换档杆实现前进后退,方向盘左右转动、暂停按钮等控制直流电机的正转、反转、暂停,使得电机驱动的遥控船模实现前进后退、左右转向、暂停等功能,有效解决了驱动功率小和船模之间相互干扰等问题,可广泛应用于遥控船模领域.Using STC12C5A60S2 single-chip microcomputer as the controller and 2.4 G(JF24D)wireless remote control module for wireless transmission and reception, a dual-motor remote control ship model control system is designed. The system realizes forward and backward by switching the gear lever. The steering wheel rotates left and right and the pause button controls the forward, reverse and pause of the dc motor. The remote controller of ship model driven by the motor realizes forward and backward, left and right steering, pause and other functions. The ship model control system can effectively solve the problems of small driving power and mutual interference between ship models, and can be widely used in the field of remote controller of ship model.
上传时间： 2022-03-27
上传用户：
板子采用4层PCB，层叠情况：Top -> GND -> Power -> Bottom板子芯片情况：(1) FPGA: Xilinx Spartan6系列的XC6SLX16-FTG256(2) DDR3: Micron的MT41J128M16，2Gbit存储容量(2) 电源：采用2片Onsemi的NCP1529分别为FPGA Core 1.2V和DDR3 1.5V提供电源FPGA的1.2V VDDCore电压，1.5V的DDR3供电电压，VREF的0.75V电压都OK。往FPGA内部下载点灯程序OK，往SPI FLASH固化程序也OK。下一步，DDR3 的MCB实现
标签： ddr3
上传时间： 2022-06-13
上传用户：ttalli
說明：1，测试交流电源（Test AC Power Supply）：A.中国（China）：AC 220V+/-2%50Hz+/-2%B.美国（United States of America）：AC 120V+/-2%60Hz+/-2%。C.英国（Britain）：AC 240V+/-2%50Hz+/-2%D.欧洲（Europe）：AC 230V+/-2%50Hz+/-2%E.日本（Japan）：AC 100V+/-2%60Hz+/-2%F.墨西哥（Mexico）：AC 127V+/-2%60Hz+/-2%2，测试温度条件（Test Temperature Conditions）：25℃+/-2℃。3，测试以右声道为准（Standard Test Use Right Channell）4，信号由AUX插座输入（Signal From AUX Jack Input）。5，测试以音量最大，音调和平衡在中央位置（电子音调在正常状态）。（Test Volume Setup Max，Equalizer And Balance Setup Center）。6，标准輸出（Standard Output）：A.输入1 KHz频率信号（Input 1 KHz Frequency Signal）B.左右声道输入信号测试右声道（L&R Input Signal Test Use R Channel）C.额定输出功率満（Rating Output Power Full）10 W，标准输出定为1w.（Rating Output Power Full 10 w，Standard Output Setup 1 W）D.额定输出功率1W到10w，标准输出定为500 mW（Rating Output Power 1 W To 10 W，Standard Output Setup 500 mW）E.额定输出功率小于1w，标准输出定为50 mW（Rating Output Power Not Full 1 W，Standard Output Setup 50 mW）F.标准輸出电压以V-VPR为准（Standard Output Voltage Use V-V/PR）。G.V-V/PR中P为额定输出功率，R为喇叭标称阻抗。
标签： 音响功放
上传时间： 2022-06-18
上传用户：
Legal Disclaimer Lenze Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lenze Semiconductor disclaims any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product.Lenze Semiconductor does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling Lenze Semiconductor products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Lenze Semiconductor for any damages arising or resulting from such use or sale.
上传时间： 2022-06-25
上传用户：
一、建焊盘打开建立焊盘的软件Pad Designer路径：包括采用的制式，现在选公制单位毫米，精度3，右侧问是否需要多重钻孔，这个功能一般是用于做非圆孔。一般圆孔不用勾选。下面设定钻孔样式，一般是圆孔，钻孔内部是否镀铜 plated（no plated即为不镀铜，一般用于塑胶件定位孔），再是钻孔直径，设置精度，是否偏移等。如果是表贴元件，钻孔直径设为0。如果是表面安装元件，把signle layer mode勾选。焊盘一般需要 begin layer和end layer，还有就是soldmask_top，soldmask_bottom，pastemask top，pastemask bottom这几个层面。对表面安装元件来说，只需要begin layer，soldermask_top以及pastemask_top就可以了。鼠标左键点击begin layer，会发现最下面三个对话框被刷新，在下面填入需要的值：从左到右：规则焊盘，热焊盘，反焊盘。1规则焊盘下面需要填入焊盘形状，长宽，是否有偏移。1热焊盘，要求选择焊盘类型，尺寸等；1反焊盘，作用是设定焊盘与周边间距，一般比规则焊盘略大6-10mil。鼠标点击soldermask_top，下面对话框刷新出该选项。按照需要填入数据。Pastemask top同样处理。右边上角还有视图角度选择，Xsection为水平视图，TOP为从上往下看。
标签： cadence allegro
上传时间： 2022-07-02
上传用户：XuVshu
PrefaceDuring the past years, there has been a quickly rising interest in radio access technologies for providingmobile as well as nomadic and fixed services for voice, video, and data. The difference indesign, implementation, and use between telecom and datacom technologies is also becoming moreblurred. One example is cellular technologies from the telecom world being used for broadband dataand wireless LAN from the datacom world being used for voice-over IP.Today, the most widespread radio access technology for mobile communication is digital cellular,with the number of users passing 5 billion by 2010, which is more than half of the world’s population.It has emerged from early deployments of an expensive voice service for a few car-borne users,to today’s widespread use of mobile-communication devices that provide a range of mobile servicesand often include camera, MP3 player, and PDA functions. With this widespread use and increasinginterest in mobile communication, a continuing evolution ahead is foreseen.This book describes LTE, developed in 3GPP (Third Generation Partnership Project) and providingtrue 4G broadband mobile access, starting from the first version in release 8 and through the continuingevolution to release 10, the latest version of LTE. Release 10, also known as LTE-Advanced,is of particular interest as it is the major technology approved by the ITU as fulfilling the IMTAdvancedrequirements. The description in this book is based on LTE release 10 and thus provides acomplete description of the LTE-Advanced radio access from the bottom up.Chapter 1 gives the background to LTE and its evolution, looking also at the different standardsbodies and organizations involved in the process of defining 4G. It also gives a discussion of the reasonsand driving forces behind the evolution.Chapters 2–6 provide a deeper insight into some of the technologies that are part of LTE and itsevolution. Because of its generic nature, these chapters can be used as a background not only for LTEas described in this book, but also for readers who want to understand the technology behind othersystems, such as WCDMA/HSPA, WiMAX, and CDMA2000.Chapters 7–17 constitute the main part of the book. As a start, an introductory technical overviewof LTE is given, where the most important technology components are introduced based onthe generic technologies described in previous chapters. The following chapters provide a detaileddescription of the protocol structure, the downlink and uplink transmission schemes, and the associatedmechanisms for scheduling, retransmission and interference handling. Broadcast operation andrelaying are also described. This is followed by a discussion of the spectrum flexibility and the associated
上传时间： 2022-07-08
上传用户：
影响共面波导特性阻抗的主要因素有，基材介电常数（通常为 4.2～4.6，这里取 4.4）、信号层与参考地间距 H、线宽 W、对地间隙 S、铜皮厚度 T。表 1 列出了不同信号层与参考地间距 H 和铜皮厚度 T=0.035mm时，50 欧姆特性阻抗对应的线宽 W 及对地间隙 S 推荐值：表 1：不同信号层与参考地间距所对应的 50 欧姆共面波导线宽及对地间距推荐值如果是 2 层板，信号层为 Top 层，参考地为 Bottom 层，如下图 3。如果是 4 层板，参考地可以是第 2层、第 3 层或者第 4 层。若参考地是第 3 层，信号层正下方第 2 层要禁铺，禁铺区域的宽度至少是信号线宽的 5 倍，如下图 4。若参考地是第 4 层，信号层正下方第 2 层和第 3 层都要禁铺，禁铺区域的宽度至少是信号线宽的 5 倍，如下图 5。如果是 6 层板以上以此类推。
标签： 射频
上传时间： 2022-07-17
上传用户：
