LTC®2366 及其较慢速的版本提供了一种高性能的替代方案，如表 1 中的 AC 规格所示。您不妨将这些有保证的规格与自己现用微控制器内置的 ADC 进行一番比较。
上传时间： 2013-11-20
上传用户：15527161163
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上传时间： 2014-12-23
上传用户：781354052
分析了ZCS PWM DC/DC变换器电路的工作原理,探讨了主要参数的设定,并建立了基于Matlab的仿真模型,通过选择参数对仿真模型和程序进行校核和调试.
上传时间： 2013-11-02
上传用户：diets
Many 8-bit and 16-bit microcontrollers feature 10-bitinternal ADCs. A few include 12-bit ADCs, but these oftenhave poor or nonexistent AC specifi cations, and certainlylack the performance to meet the needs of an increasingnumber of applications. The LTC®2366 and its slowerspeed versions offer a high performance alternative, asshown in the AC specifi cations in Table 1. Compare theseguaranteed specifi cations with the ADC built into yourcurrent microcontroller.
上传时间： 2013-10-26
上传用户：jackandlee
DC-DC经典PCB布局
上传时间： 2013-11-03
上传用户：
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
介绍了独立太阳能光伏发电的意义，采用非隔离型Boost/Buck拓扑结构为主电路拓扑，重点分析了主电路的工作原理。设计了基于TMS320LF2812的控制系统硬件电路、控制系统软件及数字PID控制器，给出了基于数字化控制的双向DC-DC变换器的充放电试验、升降压快速切换试验及其技术参数。数字化控制双向DC-DC变换器实现了太阳能板、蓄电池二者之间的稳定充放电及其快速切换。
上传时间： 2014-12-24
上传用户：arnold
DC转DC直流输出可调稳压模块
上传时间： 2013-12-01
上传用户：dudu1210004
LM2577 DC转DC升压模块
上传时间： 2013-10-08
上传用户：thesk123
为了提高光伏发电系统的转换效率，对降压式、升压式、升降压式这3种转换电路的电路结构和工作原理进行详细的分析。由这3种电路的等效电路图，在MATLAB/Simulink的环境下建立这3种电路的仿真模型，通过仿真的输出结果，计算比较它们的转换效率的高低，最终确定升压式转换电路作为光伏发电系统的DC-DC转换电路。
上传时间： 2014-01-15
上传用户：ttpay
