The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
Vishay新型功率MOSFET采用反向导引TO-252DPAK封装
上传时间： 2013-11-09
上传用户：immanuel2006
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
6小时学会labview, labview Six Hour Course – Instructor Notes This zip file contains material designed to give students a working knowledge of labview in a 6 hour timeframe. The contents are: Instructor Notes.doc – this document. labviewIntroduction-SixHour.ppt – a PowerPoint presentation containing screenshots and notes on the topics covered by the course. Convert C to F (Ex1).vi – Exercise 1 solution VI. Convert C to F (Ex2).vi – Exercise 2 solution subVI. Thermometer-DAQ (Ex2).vi – Exercise 2 solution VI. Temperature Monitor (Ex3).vi – Exercise 3 solution VI. Thermometer (Ex4).vi – Exercise 4 solution subVI. Convert C to F (Ex4).vi – Exercise 4 solution subVI. Temperature Logger (Ex4).vi – Exercise 4 solution VI. Multiplot Graph (Ex5).vi – Exercise 5 solution VI. Square Root (Ex6).vi – Exercise 6 solution VI. State Machine 1 (Ex7).vi – Exercise 7 solution VI. The slides can be presented in two three hour labs, or six one hour lectures. Depending on the time and resources available in class, you can choose whether to assign the exercises as homework or to be done in class. If you decide to assign the exercises in class, it is best to assign them in order with the presentation. This way the students can create VI’s while the relevant information is still fresh. The notes associated with the exercise slide should be sufficient to guide the students to a solution. The solution files included are one possible solution, but by no means the only solution.
标签： labview
上传时间： 2013-10-13
上传用户：zjwangyichao
ADS to MDK 转换例程由西安毕博制作的MDK指导视频，下载后打开Realview mdk1.htm页面即可播放，内容包括：模拟仿真、开发环境的建立、启动代码概述等，是您尽快上手MDK的好工具
上传时间： 2013-12-21
上传用户：dalidala
When I started writing the first edition of RF Power Amplifiers for Wireless Communications,some time back in 1997, it seemed that I was roaming a largely uninhabitedlandscape. For reasons still not clear to me there were few, if any, otherbooks dedicated to the subject of RF power amplifiers. Right at the same time, however,hundreds of engineers were being assigned projects to design PAs for wirelesscommunications products. It was not, therefore, especially difficult to be successfulwith a book that was fortuitously at the right place and the right time.
标签： Communications Amplifiers Wireless Edition
上传时间： 2013-11-12
上传用户：YYRR
Abstract: This application note helps system designers choose the correct external components for use with the MAX16948 dualremote antenna LDO/switch, thus ensuring that automobile-regulated phantom antenna supply and output-current-monitoring circuitrymeet performance objectives. An electronic calculator is provided that helps specify the critical external components for theMAX16948, thus reducing design time. The calculator also determines the device's analog output voltage, output current-limitthreshold, and output current-sensing accuracies. The calculator includes new automatic Step By Step feature that assists designerswith component choice. To use the new automatic feature, click on the Step By Step button relative to the desired section.
上传时间： 2013-11-04
上传用户：lhll918
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
通过比较各种隔离数字通信的特点和应用范围，指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口，有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路，说明设计过程中的注意事项，对光收发模块的电压特性和频率特性进行全面试验，并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明，该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上传时间： 2014-01-10
上传用户：gundan
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
