Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上传时间： 2014-03-25
上传用户：yyyyyyyyyy
The LTC®3207/LTC3207-1 is a 600mA LED/Camera driverwhich illuminates 12 Universal LEDs (ULEDs) and onecamera fl ash LED. The ULEDs are considered universalbecause they may be individually turned on or off, setin general purpose output (GPO) mode, set to blink at aselected on-time and period, or gradate on and off at aselected gradation rate. This device also has an externalenable (ENU) pin that may be used to blink, gradate, orturn on/off the LEDs without using the I2C bus. This may beuseful if the microprocessor is in sleep or standby mode. Ifused properly, these features may save valuable memoryspace, programming time, and reduce the I2C traffi c.
上传时间： 2014-01-04
上传用户：LANCE
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
上传时间： 2014-12-31
上传用户：zhuoying119
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
上传时间： 2013-10-28
上传用户：15501536189
解压密码：www.elecfans.com 随着微电子技术的迅速发展以及集成电路规模不断提高，对电路性能的设计 要求越来越严格，这势必对用于大规模集成电路设计的EDA 工具提出越来越高的 要求。自1972 年美国加利福尼亚大学柏克莱分校电机工程和计算机科学系开发 的用于集成电路性能分析的电路模拟程序SPICE（Simulation Program with IC Emphasis）诞生以来，为适应现代微电子工业的发展，各种用于集成电路设计的 电路模拟分析工具不断涌现。HSPICE 是Meta-Software 公司为集成电路设计中 的稳态分析，瞬态分析和频域分析等电路性能的模拟分析而开发的一个商业化通 用电路模拟程序，它在柏克莱的SPICE（1972 年推出），MicroSim公司的PSPICE （1984 年推出）以及其它电路分析软件的基础上，又加入了一些新的功能，经 过不断的改进，目前已被许多公司、大学和研究开发机构广泛应用。HSPICE 可 与许多主要的EDA 设计工具，诸如Candence,Workview 等兼容，能提供许多重要 的针对集成电路性能的电路仿真和设计结果。采用HSPICE 软件可以在直流到高 于100MHz 的微波频率范围内对电路作精确的仿真、分析和优化。在实际应用中， HSPICE能提供关键性的电路模拟和设计方案，并且应用HSPICE进行电路模拟时， 其电路规模仅取决于用户计算机的实际存储器容量。 The HSPICE Integrator Program enables qualified EDA vendors to integrate their products with the de facto standard HSPICE simulator, HSPICE RF simulator, and WaveView Analyzer™. In addition, qualified HSPICE Integrator Program members have access to HSPICE integrator application programming interfaces (APIs). Collaboration between HSPICE Integrator Program members will enable customers to achieve more thorough design verification in a shorter period of time from the improvements offered by inter-company EDA design solutions.
上传时间： 2013-11-10
上传用户：123312
This book is about the digital logic design of microprocessors. It is intended to provide both an understanding of the basic principles of digital logic design, and how these fundamental principles are applied in the building of complex microprocessor circuits using current technologies.
上传时间： 2013-10-14
上传用户：leyesome
ExpressPCB 是一款免费的PCB设计软件，简单实使。可以画双层板。 Our Free PCB software is a snap to learn and use. For the first time, designing circuit boards is simple for the beginner and efficient for the professional. Our board manufacturing service makes top quality two and four layer PCBs. Use our MiniBoard service and pay only $51 for three boards (plus $8 shipping).
标签： ExpressPCB PCB 设计软件
上传时间： 2013-11-15
上传用户：lchjng
mm to mil tool,mm to mil tool_mm转mil转换工具
上传时间： 2013-10-31
上传用户：515414293
ExpressPCB 是一款免费的PCB设计软件，简单实使。可以画双层板。 Our Free PCB software is a snap to learn and use. For the first time, designing circuit boards is simple for the beginner and efficient for the professional. Our board manufacturing service makes top quality two and four layer PCBs. Use our MiniBoard service and pay only $51 for three boards (plus $8 shipping).
标签： ExpressPCB PCB 设计软件
上传时间： 2013-10-09
上传用户：1047385479
mm to mil tool,mm to mil tool_mm转mil转换工具
上传时间： 2013-11-14
上传用户：crazyer
