Construction Strategy of ESD Protection CircuitAbstract： The principles used to construct ESD protection on circuits and the basic conceptions of ESD protection design are presented.Key words：ESD protection/On circuit, ESD design window, ESD current path1 引言静电放电（ESD，Electrostatic Discharge）给电子器件环境会带来破坏性的后果。它是造成集成电路失效的主要原因之一。随着集成电路工艺不断发展，互补金属氧化物半导体（CMOS，Complementary Metal-Oxide Semiconductor）的特征尺寸不断缩小，金属氧化物半导体(MOS, Metal-Oxide Semiconductor)的栅氧厚度越来越薄，MOS 管能承受的电流和电压也越来越小，因此要进一步优化电路的抗ESD 性能，需要从全芯片ESD 保护结构的设计来进行考虑。
标签： Construction Strategy ESD of
上传时间： 2013-11-09
上传用户：Aidane
模拟集成电路的设计与其说是一门技术，还不如说是一门艺术。它比数字集成电路设计需要更严格的分析和更丰富的直觉。严谨坚实的理论无疑是严格分析能力的基石，而设计者的实践经验无疑是诞生丰富直觉的源泉。这也正足初学者对学习模拟集成电路设计感到困惑并难以驾驭的根本原因。.美国加州大学洛杉机分校(UCLA)Razavi教授凭借着他在美国多所著名大学执教多年的丰富教学经验和在世界知名顶级公司(AT&T，Bell Lab，HP)卓著的研究经历为我们提供了这本优秀的教材。本书自2000午出版以来得到了国内外读者的好评和青睐，被许多国际知名大学选为教科书。同时，由于原著者在世界知名顶级公司的丰富研究经历，使本书也非常适合作为CMOS模拟集成电路设计或相关领域的研究人员和工程技术人员的参考书。... 本书介绍模拟CMOS集成电路的分析与设计。从直观和严密的角度阐述了各种模拟电路的基本原理和概念，同时还阐述了在SOC中模拟电路设计遇到的新问题及电路技术的新发展。本书由浅入深，理论与实际结合，提供了大量现代工业中的设计实例。全书共18章。前10章介绍各种基本模块和运放及其频率响应和噪声。第11章至第13章介绍带隙基准、开关电容电路以及电路的非线性和失配的影响，第14、15章介绍振荡器和锁相环。第16章至18章介绍MOS器件的高阶效应及其模型、CMOS制造工艺和混合信号电路的版图与封装。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 Feedback 9 Operational Amplifiers 10 Stability and Frequency Compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
上传时间： 2014-12-23
上传用户：杜莹12345
2400W-SPWM驱动电路，Backup of 修改2400W-SPWM驱动电路。
上传时间： 2013-11-14
上传用户：dddddd
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with high-side inductor current
上传时间： 2013-11-20
上传用户：stewart·
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
上传时间： 2014-12-24
上传用户：jasson5678
Alkaline batteries are convenient because they’re easy tofi nd and relatively inexpensive, making them the powersource of choice for portable instruments and devicesused for outdoor recreation. Their long shelf life alsomakes them an excellent choice for emergency equipmentthat may see infrequent use but must be ready to go on amoment’s notice. It is important that the DC/DC convertersin portable devices operate over the widest possiblebattery voltage range to extend battery run time, and thussave the user from frequent battery replacement.
上传时间： 2014-12-24
上传用户：569342831
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
The LTC®4099 high effi ciency USB power manager andLi-Ion/Polymer battery charger seamlessly managespower distribution from multiple sources in portableapplications. It is differentiated from other USB powermanagers by its bidirectional I2C port that allows the hostmicroprocessor to control and monitor all aspects of theUSB power management and battery charging processes.In addition, a programmable interrupt generation functionalerts the host microprocessor to changes in device statusand provides unprecedented control of power managementfunctions. This high degree of confi gurability allowspost-layout changes in operation, even changes in thefi eld, and it allows a single qualifi ed device to be usedin a variety of products, thus reducing design time andeasing inventory management.
上传时间： 2013-10-22
上传用户：18602424091
