所学的指令LD、LDI、OUT AND、ANI OR、 ORI LDP、 LDF、ANDP、ANDF、 ORP、 ORF ORB、 ANB MPS、 MRD、 MPP MC、 MCRSET RSTNOP END 自锁电路触点的动作发光二极管的工作原理。八段码显示是利用发光二极管的不同段码组合来实现的，它可以实现0到F的显示。抢答器的显示就是利用八段码显示的特性，来完成几个不同组别的显示。用PLC实现八段码显示0～9组的3组以上抢答器的程序编写，并完成以下要求：1）设计由PLC实现的八段码显示0～9组的3组以上抢答器的程序编写，并完成以下要求： ①列出PLC的输入输出地址分配表 ②画出PLC的输入输出接线图（即I/O接线图） ③设计PLC的梯形图 ④根据梯形图列写指令表 2）按PLC控制I/O口（输入/输出）接线图在模拟实验设备上正确接线。
上传时间： 2013-11-22
上传用户：lmeeworm
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上传时间： 2013-11-02
上传用户：zw380105939
提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制Con trol System of Stepp ingMotor Ba sed on AT89C52 ChipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing motor controller.KEY WORDS: Chip microcomputer; Stepp ingmotor; DCSSR; Real2time control
标签： Control System ingMot Stepp
上传时间： 2013-11-19
上传用户：leesuper
MCSÉ-51 Programmer's Guide and Instruction Set The information presented in this chapter is collected from the MCSÉ-51 Architectural Overview and the HardwareDescription of the 8051, 8052 and 80C51 chapters of this book. The material has been selected and rearranged toform a quick and convenient reference for the programmers of the MCS-51. This guide pertains specifically to the8051, 8052 and 80C51.
上传时间： 2013-11-13
上传用户：hj_18
The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
上传时间： 2013-11-10
上传用户：1427796291
什么是JTAG 到底什么是JTAG呢？ JTAG(Joint Test Action Group)联合测试行动小组)是一种国际标准测试协议（IEEE 1149.1兼容），主要用于芯片内部测试。现在多数的高级器件都支持JTAG协议，如DSP、FPGA器件等。标准的JTAG接口是4线：TMS、 TCK、TDI、TDO，分别为模式选择、时钟、数据输入和数据输出线。 JTAG最初是用来对芯片进行测试的，基本原理是在器件内部定义一个TAP（Test Access Port�测试访问口）通过专用的JTAG测试工具对进行内部节点进行测试。JTAG测试允许多个器件通过JTAG接口串联在一起，形成一个JTAG链，能实现对各个器件分别测试。现在，JTAG接口还常用于实现ISP（In-System rogrammable�在线编程），对FLASH等器件进行编程。 JTAG编程方式是在线编程，传统生产流程中先对芯片进行预编程现再装到板上因此而改变，简化的流程为先固定器件到电路板上，再用JTAG编程，从而大大加快工程进度。JTAG接口可对PSD芯片内部的所有部件进行编程 JTAG的一些说明 通常所说的JTAG大致分两类，一类用于测试芯片的电气特性，检测芯片是否有问题；一类用于Debug；一般支持JTAG的CPU内都包含了这两个模块。 一个含有JTAG Debug接口模块的CPU，只要时钟正常，就可以通过JTAG接口访问CPU的内部寄存器和挂在CPU总线上的设备，如FLASH，RAM，SOC（比如4510B，44Box，AT91M系列）内置模块的寄存器，象UART，Timers，GPIO等等的寄存器。 上面说的只是JTAG接口所具备的能力，要使用这些功能，还需要软件的配合，具体实现的功能则由具体的软件决定。 例如下载程序到RAM功能。了解SOC的都知道，要使用外接的RAM，需要参照SOC DataSheet的寄存器说明，设置RAM的基地址，总线宽度，访问速度等等。有的SOC则还需要Remap，才能正常工作。运行Firmware时，这些设置由Firmware的初始化程序完成。但如果使用JTAG接口，相关的寄存器可能还处在上电值，甚至时错误值，RAM不能正常工作，所以下载必然要失败。要正常使用，先要想办法设置RAM。在ADW中，可以在Console窗口通过Let 命令设置，在AXD中可以在Console窗口通过Set命令设置。
上传时间： 2013-10-23
上传用户：aeiouetla
This application note covers the design considerations of a system using the performance features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The design focuses on high system throughput through the AXI Interconnect core with F MAX and area optimizations in certain portions of the design. The design uses five AXI video direct memory access (VDMA) engines to simultaneously move 10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary video timing signals. Data read by each AXI VDMA is sent to a common on-screen display (OSD) core capable of multiplexing or overlaying multiple video streams to a single output video stream. The output of the OSD core drives the DVI video display interface on the board. Performance monitor blocks are added to capture performance data. All 10 video streams moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are controlled by a MicroBlaze™ processor. The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the Xilinx® ML605 Rev D evaluation board
上传时间： 2013-11-14
上传用户：fdmpy
介绍了AES中,SubBytes算法在FPGA的具体实现.构造SubBytes的S-Box转换表可以直接查找ROM表来实现.通过分析SubBytes算法得到一种可行性硬件逻辑电路,从而实现SubBytes变换的功能.
上传时间： 2013-11-30
上传用户：hzy5825468
