HCS12微控制器MC9S12DP256 第一步： 1) HCS12 技术概述2) Operating Modes工作模式3) Resource Mapping资源映射4) External Bus Interface外部总线接口5) Port Integration Module端口集成模块6) Background Debug Mode背景调试模块
上传时间： 2013-12-20
上传用户：源码3
本文介绍了一种基于单片机的健身车转速测量系统。该系统具有电路简单、使用方便等特点。文中详细介绍了该系统的工作原理,并且给出了它的硬件原理图和软件设计程序框图。关键词:转速 单片机 测量ABSTRACT :This paper introduces a measuring system of the rotational velocity of exercise bike based on single - chip microcomputer . It has such advantages : simple circuit ,convenient use and so on. The work principle is presented in detail in this paper and the block diagram of hardware and program flow chart are giv2 en as well .KEYWORDS :Rotational velocity Single - chip microcomputer Measuring
上传时间： 2013-11-02
上传用户：源弋弋
自动检测80C51串行通讯中的波特率:本文介绍一种在80C51 串行通讯应用中自动检测波特率的方法。按照经验，程序起动后所接收到的第1 个字符用于测量波特率。这种方法可以不用设定难于记忆的开关，还可以免去在有关应用中使用多种不同波特率的烦恼。人们可以设想：一种可靠地实现自动波特检测的方法是可能的，它无须严格限制可被确认的字符。问题是：在各种的条件下，如何可以在大量允许出现的字符中找出波特率定时间隔。显然，最快捷的方法是检测一个单独位时间（single bit time），以确定接收波特率应该是多少。可是，在RS-232 模式下，许多ASCII 字符并不能测量出一个单独位时间。对于大多数字符来说，只要波特率存在合理波动（这里的波特率是指标准波特率），从起始位到最后一位“可见”位的数据传输周期就会在一定范围内发生变化。此外，许多系统采用8 位数据、无奇偶校验的格式传输ASCII 字符。在这种格式里，普通ASCII 字节不会有MSB 设定，并且，UART总是先发送数据低位（LSB），后发送数据高位（MSB），我们总会看见数据的停止位。在下面的波特率检测程序中，先等待串行通讯输入管脚的起始信号（下降沿），然后起动定时器T0。在其后的串行数据的每一个上升沿，将定时器T0 的数值捕获并保存。当定时器T0溢出时，其最后一次捕获的数值即为从串行数据起始位到最后一个上升沿（我们假设是停止位）过程所持续的时间。
上传时间： 2014-08-22
上传用户：dajin
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-10-10
上传用户：inwins
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The TRS232E is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/RS-232-Fvoltage levels from a single 5-V supply. Each receiver converts TIA/RS-232-F inputs to 5-V TTL/CMOS levels.This receiver has a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Eachdriver converts TTL/CMOS input levels into TIA/RS-232-F levels. The driver, receiver, and voltage-generatorfunctions are available as cells in the Texas Instruments LinASIC™ library.
上传时间： 2013-10-07
上传用户：waitingfy
The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
标签： Stellaris Clocking Options for
上传时间： 2013-10-14
上传用户：pol123
基于单DSP的VoIP模拟电话适配器研究与实现:提出和实现了一种新颖的基于单个通用数字信号处理器(DSP)的VoIP模拟电话适配器方案。DSP的I/O和存储资源非常有限，通常适于运算密集型应用，不适宜控制密集型应用[5]。该系统高效利用单DSP的I/O和片内外存储器资源，采用μC/OS-II嵌入式实时操作系统，支持SIP和TCP-UDP/IP协议，通过LAN或者宽带接入，使普通电话机成为Internet终端，实现IP电话。该系统软硬件结构紧凑高效，运行稳定，成本低，具有广阔的应用前景。关键词：模拟电话适配器；IP电话；数字信号处理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上传时间： 2013-11-20
上传用户：Wwill
Proteus6.9和Keil联调方法及破解文件下载:方法:1.安装proteus6.9和keil吧2.安装压缩包里面的vdmagdi.exe文件,安装完后keil\c51\bin\文件夹里面会有VDM51.DLL这个.3.把压缩包里面的PROSPICE.DLL复制到Proteus6Professional\bin目录下,覆盖已经有的.4.打开keil,打开optionfortarget里面的debug选项卡,选择ProteusVSMSimulator,并进行相关设置.(两台计算机联调得输入正确的host IP和port号)5,打开isis,选择debug\useremotedebugmonitor.这样就可以啦,试试看吧!
上传时间： 2013-10-15
上传用户：wenwiang
基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
上传时间： 2013-10-13
上传用户：cicizoe
