This leon3 design is tailored to the Altera NiosII Startix2 Development board, with 16-bit DDR SDRAM and 2 Mbyte of SSRAM. As of this time, the DDR interface only works up to 120 MHz. At 130, DDR data can be read but not written. NOTE: the test bench cannot be simulated with DDR enabled because the Altera pads do not have the correct delay models. * How to program the flash prom with a FPGA programming file 1. Create a hex file of the programming file with Quartus. 2. Convert it to srecord and adjust the load address: objcopy --adjust-vma=0x800000 output_file.hexout -O srec fpga.srec 3. Program the flash memory using grmon: flash erase 0x800000 0xb00000 flash load fpga.srec
标签： Development Startix2 tailored Altera
上传时间： 2014-01-19
上传用户：chongcongying
The preferred technique places the new YAMON in the opposite Flash bank (the Db1200 boards have two Flash banks), and then changes switch S11 to swap the Flash banks in the memory map to allow the other Flash bank to become the boot bank. This technique is the safest and preferred method since it preserves the existing YAMON
标签： the preferred technique opposite
上传时间： 2016-02-27
上传用户：thuyenvinh
Testability is the concern most often voiced by Texas Instruments (TIä ) application specific integrated circuit (ASIC) users. This document is intended to consolidate TI policies into a coherent approach to designing for testability. It is not intended as a specification, but as a guide you can use for developing test strategies when designs are being initiated
标签： Testability Instruments application specific
上传时间： 2016-11-13
上传用户：wfl_yy
TMS320C6711的上电自检 This source code is ultimately used to create a JEDEC programming file used * to program the Flash ROM on the C6711 DSK.
标签： used programming ultimately source
上传时间： 2013-12-12
上传用户：wl9454
LPC178* 177*用户手册 LPC178x/7x 32-bit ARM Cortex-M3 microcontroller; up to 512 kB flash and 96 kB SRAM; USB Device/Host/OTG; Ethernet; LCD; EMC Rev. 3 — 27 December 2011 Objective data sheet
上传时间： 2013-04-24
上传用户：胡佳明胡佳明
The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
This article has been contributed to the TI Developer Wiki. To see the most recently updated version or tocontribute, visit this topic at:
上传时间： 2013-11-04
上传用户：钓鳌牧马
STM32L053C8T6数据手册Features • Ultra-low-power platform – 1.65 V to 3.6 V power supply – -40 to 125 °C temperature range – 0.27 µA Standby mode (2 wakeup pins) – 0.4 µA Stop mode (16 wakeup lines) – 0.8 µA Stop mode + RTC + 8 KB RAM retention – 139 µA/MHz Run mode at 32 MHz – 3.5 µs wakeup time (from RAM) – 5 µs wakeup time (from Flash) • Core: ARM® 32-bit Cortex®-M0+ with MPU – From 32 kHz up to 32 MHz max. – 0.95 DMIPS/MHz • Reset and supply management – Ultra-safe, low-power BOR (brownout reset) with 5 selectable thresholds – Ultralow power POR/PDR – Programmable voltage detector (PVD) • Clock sources – 1 to 25 MHz crystal oscillator – 32 kHz oscillator for RTC with calibration – High speed internal 16 MHz factory-trimmed RC (+/- 1%) – Internal low-power 37 kHz RC – Internal multispeed low-power 65 kHz to 4.2 MHz RC – PLL for CPU clock • Pre-programmed bootloader – USART, SPI supported • Development support – Serial wire debug supported • Up to 51 fast I/Os (45 I/Os 5V tolerant) • Memories – Up to 64 KB Flash with ECC – 8KB RAM – 2 KB of data EEPROM with ECC – 20-byte backup register
标签： stm32l053c8t6
上传时间： 2022-02-06
上传用户：
program to trasmit data to a TI92 with the TI Graph-Link
标签： Graph-Link program trasmit data
上传时间： 2015-01-03
上传用户：youke111
Flash Programmer through JTAG for sa
标签： Programmer through Flash JTAG
上传时间： 2013-12-18
上传用户：xzt
