The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
上传时间： 2013-11-04
上传用户：as275944189
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
P C B 可测性设计布线规则之建议― ― 从源头改善可测率PCB 设计除需考虑功能性与安全性等要求外，亦需考虑可生产与可测试。这里提供可测性设计建议供设计布线工程师参考。1. 每一个铜箔电路支点，至少需要一个可测试点。如无对应的测试点，将可导致与之相关的开短路不可检出，并且与之相连的零件会因无测试点而不可测。2. 双面治具会增加制作成本，且上针板的测试针定位准确度差。所以Layout 时应通过Via Hole 尽可能将测试点放置于同一面。这样就只要做单面治具即可。3. 测试选点优先级：A.测垫(Test Pad) B.通孔(Through Hole) C.零件脚(Component Lead) D.贯穿孔(Via Hole)(未Mask)。而对于零件脚，应以AI 零件脚及其它较细较短脚为优先，较粗或较长的引脚接触性误判多。4. PCB 厚度至少要62mil(1.35mm)，厚度少于此值之PCB 容易板弯变形，影响测点精准度，制作治具需特殊处理。5. 避免将测点置于SMT 之PAD 上，因SMT 零件会偏移，故不可靠，且易伤及零件。6. 避免使用过长零件脚(>170mil(4.3mm))或过大的孔(直径>1.5mm)为测点。7. 对于电池(Battery)最好预留Jumper，在ICT 测试时能有效隔离电池的影响。8. 定位孔要求：(a) 定位孔(Tooling Hole)直径最好为125mil(3.175mm)及其以上。(b) 每一片PCB 须有2 个定位孔和一个防呆孔(也可说成定位孔,用以预防将PCB反放而导致机器压破板)，且孔内不能沾锡。(c) 选择以对角线，距离最远之2 孔为定位孔。(d) 各定位孔(含防呆孔)不应设计成中心对称,即PCB 旋转180 度角后仍能放入PCB,这样,作业员易于反放而致机器压破板)9. 测试点要求：(e) 两测点或测点与预钻孔之中心距不得小于50mil(1.27mm)，否则有一测点无法植针。以大于100mil(2.54mm)为佳，其次是75mil(1.905mm)。(f) 测点应离其附近零件(位于同一面者)至少100mil，如为高于3mm 零件，则应至少间距120mil，方便治具制作。(g) 测点应平均分布于PCB 表面，避免局部密度过高，影响治具测试时测试针压力平衡。(h) 测点直径最好能不小于35mil(0.9mm)，如在上针板，则最好不小于40mil(1.00mm)，圆形、正方形均可。小于0.030”(30mil)之测点需额外加工，以导正目标。(i) 测点的Pad 及Via 不应有防焊漆(Solder Mask)。(j) 测点应离板边或折边至少100mil。(k) 锡点被实践证实是最好的测试探针接触点。因为锡的氧化物较轻且容易刺穿。以锡点作测试点，因接触不良导致误判的机会极少且可延长探针使用寿命。锡点尤其以PCB 光板制作时的喷锡点最佳。PCB 裸铜测点，高温后已氧化，且其硬度高，所以探针接触电阻变化而致测试误判率很高。如果裸铜测点在SMT 时加上锡膏再经回流焊固化为锡点，虽可大幅改善，但因助焊剂或吃锡不完全的缘故，仍会出现较多的接触误判。
上传时间： 2014-01-14
上传用户：cylnpy
单片机开发中除必要的硬件外，同样离不开软件，我们写的汇编语言源程序要变为CPU可以执行的机器码有两种方法，一种是手工汇编，另一种是机器汇编，目前已极少使用手工汇编的方法了。机器汇编是通过汇编软件将源程序变为机器码，用于MCS-51 单片机的汇编软件有早期的A51，随着单片机开发技术的不断发展，从普遍使用汇编语言到逐渐使用高级语言开发，单片机的开发软件也在不断发展，Keil 软件是目前最流行开发MCS-51 系列单片机的软件，这从近年来各仿真机厂商纷纷宣布全面支持Keil 即可看出。Keil 提供了包括C编译器、宏汇编、连接器、库管理和一个功能强大的仿真调试器等在内的完整开发方案，通过一个集成开发环境（uVision）将这些部份组合在一起。运行Keil 软件需要Pentium 或以上的CPU，16MB或更多RAM、20M 以上空闲的硬盘空间、WIN98、NT、WIN2000、WINXP等操作系统。掌握这一软件的使用对于使用51 系列单片机的爱好者来说是十分必要的，如果你使用C 语言编程，那么Keil 几乎就是你的不二之选（目前在国内你只能买到该软件、而你买的仿真机也很可能只支持该软件），即使不使用C 语言而仅用汇编语言编程，其方便易用的集成环境、强大的软件仿真调试工具也会令你事半功倍。我们将通过一些实例来学习Keil 软件的使用，在这一部份我们将学习如何输入源程序，建立工程、对工程进行详细的设置，以及如何将源程序变为目标代码。图1 所示电路图使用89C51 单片机作为主芯片，这种单片机性属于MCS-51 系列，其内部有4K 的FLASH ROM,可以反复擦写，非常适于做实验。89C51 的P1 引脚上接8 个发光二极管，P3.2~P3.4 引脚上接4 个按钮开关，我们的第一个任务是让接在P1 引脚上的发光二极管依次循环点亮。 一、Keil 工程的建立首先启动Keil 软件的集成开发环境，这里假设读者已正确安装了该软件，可以从桌面上直接双击uVision 的图标以启动该软件。UVison启动后，程序窗口的左边有一个工程管理窗口，该窗口有3 个标签，分别是Files、Regs、和Books，这三个标签页分别显示当前项目的文件结构、CPU 的寄存器及部份特殊功能寄存器的值（调试时才出现）和所选CPU 的附加说明文件，如果是第一次启动Keil，那么这三个标签页全是空的。
上传时间： 2013-12-26
上传用户：liulinshan2010
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上传时间： 2013-10-22
上传用户：taiyang250072
微型打印机的C语言源程序:微型打印机的C51源程序#define uchar unsigned char#define uint unsigned int#include <reg52.h>#include <stdio.h>#include <absacc.h>#include <math.h>#include <string.h>#include <ctype.h>#include <stdlib.h>#define PIN XBYTE[0x8000]#define POUT XBYTE[0x9000]sbit PRINTSTB =P1^6;sbit DOG=P1^7;bdata char pin＆#118alue;sbit PRINTBUSY=pin＆#118alue^7;sbit PRINTSEL =pin＆#118alue^6;sbit PRINTERR =pin＆#118alue^5;sbit PRINTACK =pin＆#118alue^4; void PrintString(uchar *String1,uchar *String2);void initprint(void);void print(uchar a); void initprint(void) //打印机初始化子程序 { pin＆#118alue=PIN; if((PRINTSEL==1)&&(PRINTERR==1)) { print(0x1b); print(0x40); print(0x1b); print(0x38); print(0x4); }}void print(uchar a) //打印字符a{ pin＆#118alue=PIN; if((PRINTSEL==0)||(PRINTERR==0)) return; for(;;) { DOG=~DOG; pin＆#118alue=PIN; if(PRINTBUSY==0) break; } DOG=~DOG; POUT=a; PRINTSTB=1; PRINTSTB=1; PRINTSTB=1; PRINTSTB=1; PRINTSTB=0; PRINTSTB=0; PRINTSTB=0; PRINTSTB=0; PRINTSTB=1;}void PrintString(uchar *String) //打印字符串后回车{ uchar CH; for (;;) { DOG=~DOG; CH=*String; if (CH==0) { print(0x0d); break; } print(CH); String++; } initprint();}
上传时间： 2013-10-18
上传用户：hasan2015
随着单片机开发技术的不断发展，目前已有越来越多的人从普遍使用汇编语言到逐渐使用高级语言开发，其中主要是以C语言为主，市场上几种常见的单片机均有其C语言开发环境。这里以最为流行的80C51单片机为例来学习单片机的C语言编程技术。大家都有C语言基础,但是编单片机程序,大家还得找专门的书来学习一下。这里我们只介绍Keil这种工具软件的用法。学习一种编程语言，最重要的是建立一个练习环境，边学边练才能学好。Keil软件是目最流行开发80C51系列单片机的软件，Keil提供了包括C编译器、宏汇编、连接器、库管理和一个功能强大的仿真调试器等在内的完整开发方案，通过一个集成开发环境（µVision）将这些部份组合在一起。下面我以一个实验举一个例子，一步一步学习Keil软件的使用。 首先我们看硬件原理图： 很明显，要点亮使发光二极管，必须使单片机的I/O口P1.0输出低电平。于是我们的任务就是编程序使P1.0输出地电平。1. 使用Keil前必须先安装。安装过程简单，这里不在叙述。2. 安装好了Keil软件以后，我们打开它。打开以后界面如下：
上传时间： 2013-11-07
上传用户：wtrl
