针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
主要介绍构成记忆示波器的STC12C5408AD增强型单片机8通道10位模数转换功能的设置、应用和具体的汇编程序设计，以及PC机串行通讯和图形显示的高速汇编程序的设计要点，并列举实例说明其应用效果。 Abstract: The configuration, applications and the designs for? compiling program of the memorial oscillograph of 10 bits A/D conversation are introduced. It’s bases on STC12C5408AD 8? channels? single-chip? computer? in? enhancement? mode. It also recommends the devising essentials of high speed compiling program for PC serial communication and graphics display, lists examples to explain its effects in using.
上传时间： 2013-10-10
上传用户：adada
介绍了基于单片机C8051F020的通用串口适配器的设计与实现方法，即由单片机控制的智能化一对多口收发信号转换器。通过采用C51对单片机进行编程，控制与RS-232（标准RS-232电平）、RS232(TTL电平)、RS-422接口的数据通信；采用C++ Builder作为开发平台，通过RS-232接口实现上位机对适配器各个通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
上传时间： 2013-11-19
上传用户：hebanlian
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-07
上传用户：cuibaigao
提出一种基于单片机AT89C51SND1C的MP3播放系统的设计方案。单片机集成了专用的解码器，使用K9F1208闪存作为外存储器，放音电路采用CS4330，存储文件通过播放器上的USB接口设备从PC机上直接下载，液晶显示采用LCD1602。方案设计简单，性价比高，低功耗，易扩展。由于采用的是通用单片机实现的，可以很容易地移植到其他微控制器系统中，有很强的市场竞争能力和实用价值。 Abstract: A MP3 player design based on microchip AT89C51SND1C was presented, which used K9F1208 Flash chip as the memory circuit and used CS4330 as play chip. Storage files were download from PC through USB interfaces player on the device，and the LCD/602 was used as display screen. This system had characteristics of simple design,low power,easy expand，low cost and high recognition. Using of universual microchip make it easy to transplant to other microcontrol system，and have strong market competitiom and practical value.
上传时间： 2014-12-27
上传用户：佳期如梦
摘要：介绍了采取专用电平转换芯片MAX232实现PC机与MCS51单片机之间的串行通信的方法．通过对系统的通信方式选择89C51通信波特率的设置、通信的设置，以及对接口电路的软件和硬件的设计分析，展示了该电路的实用性．关键词：微处理器；PC机；串行通信；RS-232接口；MAX232芯片
上传时间： 2014-01-22
上传用户：shizhanincc
汽车发动机电控系统的结构与维修(A)试题
上传时间： 2013-10-09
上传用户：hsfei8
摘要：提出一种全新的利用键盘接口实现单片机系统和PC机通信的方案，介绍了键盘与PC机通信的原理，并成功地应用于实际系统。该方案为外部单片机系统与3-机通信提供了一条有效的途径。关键词：键盘接口 单片机系统 时序 命令字
上传时间： 2013-11-03
上传用户：drink！
摘要：文章介绍了由PC机和80C196单片机构成的热处理温度微机控制系统，并就集中温度数据采集方法、PC机和单片机的数据通信格式、单片机软硬件设计、双向晶闸管的触发电路等相关技术进行了分析，给出了串行通信中断接收及数据处理程序设计流程图。关键词：单片机；数据通信；触发电路；温度控制
上传时间： 2013-10-20
上传用户：fnhhs
