很好的搜索： 给你很多长度不定的木棒，将他们分成几组，每组中的总长度作为这组的标示值，请给出一种分组方法，能使得所有标示值中的最小值最大。 Input 多组，每组两行，第一行是一个N和K，代表有N根木棒，分成K组，第二行是N个数字，代表木棒的长度。（N不超过100，K不超过20，每根木棒长度不超过1000） Output 输出所有标示值中的最小值的最大值。 Sample Input 5 3 1 3 5 7 9 5 3 89 59 68 35 29 Sample Output 8 89
上传时间： 2013-12-23
上传用户：nairui21
简单的floyd运用 第一行输入一个整数C。C是测试的情况（0< C <=30）.第二行一个正整数N( 0< N <=100),表示道路的总数.紧接N行，每一行包含两个字符串， Si,，Ti，和一个整数Di,代表从Si到Ti的距离(0<= Di <=150)。最后一行有两个字符串，S 和 T，你得找出从S 到 T的最短的距离。地名是不超过120个小写字符的串（从‘a’到‘z’)。假设这里最多有100条直接连通两个地方的路。 Output 输出包含C行，每一行对一种测试情况。对每一种测试情况，输出包含一个整数，假如S 到 T存在一条最短的路,输出从S到T的最短距离,否则输出“-1”. Sample Input 2 2 jiuzhouriver liuchi 89 liuchi liyuan 100 liuchi jiuzhouriver 3 youyongchi fengyuan 100 qinshi meiyuan 100 chaochang supermarkt 100 meiyuan youyongchi Sample Output 89 -1
上传时间： 2016-03-10
上传用户：wyc199288
基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation. System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
标签： simulator i.e. system-level link-level
上传时间： 2016-03-15
上传用户：xsnjzljj
无线网卡驱动 固件程序 There are currently 3 "programming generations" of Atheros 802.11 wireless devices (some of these have multiple hardware implementations but otherwise appear identical to users): 5210 supports 11a only 5211 supports both 11a and 11b 5212 supports 11a, 11b, and 11g
标签： programming generations currently wireless
上传时间： 2014-01-22
上传用户：aa54
To use the ATLTrace tool: Debug an MFC or ATL project select Start from the Debug menu. Select MFC/ATL Trace Tool in the Tools menu. Expand the tree control list in the Trace List window. Here you will see the running application, any modules within that application, and the trace categories for each module. Customize, for each process, module, and category, which information is displayed in the output window. The Trace level control in the Process group is related to the ATLTRACE2 level only those ATLTRACE2 messages with a level equal to or greater than the setting in the Trace level control will be displayed in the output window. Select Apply to put your settings into effect. You can save your settings, and load them the next time you debug the application use the Save and Load buttons.
标签： Debug the ATLTrace project
上传时间： 2014-01-15
上传用户：wfl_yy
RT2570芯片USB口无线网卡linux设备驱动程序,有调试信息输出的.-RT2570 chip USB wireless network card device driver linux, the output of debugging information.
上传时间： 2014-01-07
上传用户：gxf2016
PCI设计指南The Xilinx LogiCORE PCI interface is a fully verified, pre-implemented PCI Bus interface. This interface is available in 32-bit and 64- bit versions, with support for multiple Xilinx FPGA device families. It is designed to support both Verilog-HDL and VHDL. The design examples in this book are provided in Verilog.
标签： interface PCI pre-implemented LogiCORE
上传时间： 2016-04-03
上传用户：清风冷雨
The Unisoft software module GERBER CONNECTION (CNC-BRIDGE). GERBER CONNECTION has all the features of VIEW-MARKUP and adds the ability to open multiple gerber file layers and add information to components. It is always the preference to use the CAD data vs. gerber data. If you do not have the CAD data then GERBER CONNECTION can help.
标签： CONNECTION GERBER CNC-BRIDGE software
上传时间： 2014-01-21
上传用户：13681659100
k-meansy算法源代码。This directory contains code implementing the K-means algorithm. Source code may be found in KMEANS.CPP. Sample data isfound in KM2.DAT. The KMEANS program accepts input consisting of vectors and calculates the given number of cluster centers using the K-means algorithm. Output is directed to the screen.
标签： code implementing directory algorithm
上传时间： 2016-04-07
上传用户：shawvi
Programs in the irregular grid design package described in this manual are used to carry out five main functions: verification and adjustment of coastline and bathymetric data preparation of an irregular triangular depth grid covering the domain to be modelled production of a preliminary irregular triangular model grid with nodes suitably positioned for accurate and efficient numerical modelling interactive checking and editing, including trimming and joining, of model grid display and plotting of model output.
标签： described irregular Programs package
上传时间： 2016-04-09
上传用户：fnhhs
