Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2013-12-13
上传用户：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2014-01-20
上传用户：三人用菜
This paper presents a visual based localization mechanism for a legged robot. Our proposal, fundamented on a probabilistic approach, uses a precompiled topological map where natural landmarks like doors or ceiling lights are recognized by the robot using its on-board camera. Experiments have been conducted using the AIBO Sony robotic dog showing that it is able to deal with noisy sensors like vision and to approximate world models representing indoor ofce environments. The two major contributions of this work are the use of this technique in legged robots, and the use of an active camera as the main sensor
标签： localization mechanism presents proposal
上传时间： 2016-11-04
上传用户：dianxin61
DTNSim2 is a simulator for Delay-Tolerant Networks (DTNs) written in Java. It is based on Sushant Jain s DTNSim, which was used for the Routing in a delay tolerant network paper. It has been exensively modified.
标签： Delay-Tolerant simulator Networks DTNSim2
上传时间： 2016-11-06
上传用户：tianyi223
Feature Extraction of Infrared Target Based on Image Moment and Wavelet Energy
标签： Extraction Infrared Feature Wavelet
上传时间： 2016-11-12
上传用户：BOBOniu
Simulation of Direct Sequence Spread Spectrum Communication System Based on MATLAB
标签： Communication Simulation Sequence Spectrum
上传时间： 2014-01-21
上传用户：钓鳌牧马
Here you have the Development Kit of SkyeTek Module M1. Contains a demo software and some interesting PDF.
标签： Development interestin Contains software
上传时间： 2013-12-30
上传用户：tyler
A program based in chip TIRIS programmed in assembler. Useful for prototype design of a RFID reader.
标签： programmed assembler prototype program
上传时间： 2013-12-24
上传用户：youke111
W ireless rem ote control system for tower crane based on M SP430 and nRF905：介绍了一种基于无线遥测技术的塔吊遥控系统，该系统以MSP430超低功耗l6位微控制器和无 线收发芯片nRF905为核心。系统采用软件编码和硬件译码的方式提高了系统的抗干扰能力，系统发 射器采用定时扫描、接收器采用无记忆输出控制方式，提高了系统可靠性，该系统可广泛应用于塔吊等 一般的工业遥控系统中。
标签： ireless control system based
上传时间： 2013-12-15
上传用户：zhengzg
FatFs06.rar FatFs is a generic file system module to implement the FAT file system to small embedded systems. The FatFs is written in compliance with ANSI C, therefore it is independent of hardware architecture. It can be incorporated into cheap microcontrollers, such as 8051, PIC, AVR, SH, Z80, H8, ARM and etc..., without any change.
标签： system FatFs file implement
上传时间： 2016-11-17
上传用户：chenxichenyue
