DevKit8000评估套件简介及应用 OMAP3530应用处理器集成600-MHz ARM Cortex-A8核及430-MHz TMS320C64x DSP核 板载128MByte DDR SDRAM，32bit 板载128MByte NAND Flash
上传时间： 2014-12-27
上传用户：lliuhhui
LPC1700系列ARM是基于第二代ARM Cortex-M3内核的微控制器，是为嵌入式系统应用而设计的高性能、低功耗的32位微处理器，适用于仪器仪表、工业通讯、电机控制、灯光控制、报警系统等领域。其操作频率高达100MHz，采用3级流水线和哈佛结构，带独立的本地指令和数据总线以及用于外设的低性能的第三条总线，使得代码执行速度高达1.25MIPS/MHz，并包含1个支持随机跳转的内部预取指单元。
上传时间： 2013-11-16
上传用户：lbbyxmraon
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9671 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many more devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and more device addresses (64versus 8) to allow many more devices on the bus without address conflicts.
上传时间： 2013-10-12
上传用户：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-28
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-21
上传用户：wwwwwen5
基于单片机的LED汉字显示屏设计与制作：在大型商场、车站、码头、地铁站以及各类办事窗口等越来越多的场所需要用LED点阵显示图形和汉字。LED行业已成为一个快速发展的新兴产业，市场空间巨大，前景广阔。随着信息产业的高速发展，LED显示作为信息传播的一种重要手段，已广泛应用于室内外需要进行服务内容和服务宗旨宣传的公众场所，例如户内外公共场所广告宣传、机场车站旅客引导信息、公交车辆报站系统、证券与银行信息显示、餐馆报价信息豆示、高速公路可变情报板、体育场馆比赛转播、楼宇灯饰、交通信号灯、景观照明等。显然，LED显示已成为城市亮化、现代化和信息化社会的一个重要标志。 本文基于单片机(AT89C51)讲述了16×16 LED汉字点阵显示的基本原理、硬件组成与设计、程序编译与下载等基本环节和相关技术。2 硬件电路组成及工作原理本产品拟采用以AT89C51单片机为核心芯片的电路来实现，主要由AT89C51芯片、时钟电路、复位电路、列扫描驱动电路(74HC154)、16×16 LED点阵5部分组成，如图1所示。 其中，AT89C51是一种带4 kB闪烁可编程可擦除只读存储器(Falsh Programmable and Erasable Read OnlyMemory，FPEROM)的低电压、高性能CMOS型8位微处理器，俗称单片机。该器件采用ATMEL高密度非易失存储器制造技术制造，与工业标准的MCS-51指令集和输出管脚相兼容。由于将多功能8位CPU和闪烁存储器组合在单个芯片中，能够进行1 000次写／擦循环，数据保留时间为10年。他是一种高效微控制器，为很多嵌入式控制系统提供了一种灵活性高且价廉的方案。因此，在智能化电子设计与制作过程中经常用到AT89C51芯片。时钟电路由AT89C51的18，19脚的时钟端(XTALl及XTAL2)以及12 MHz晶振X1、电容C2，C3组成，采用片内振荡方式。复位电路采用简易的上电复位电路，主要由电阻R1，R2，电容C1，开关K1组成，分别接至AT89C51的RST复位输入端。LED点阵显示屏采用16×16共256个象素的点阵，通过万用表检测发光二极管的方法测试判断出该点阵的引脚分布，如图2所示。 我们把行列总线接在单片机的IO口，然后把上面分析到的扫描代码送人总线，就可以得到显示的汉字了。但是若将LED点阵的行列端口全部直接接入89S51单片机，则需要使用32条IO口，这样会造成IO资源的耗尽，系统也再无扩充的余地。因此，我们在实际应用中只是将LED点阵的16条行线直接接在P0口和P2口，至于列选扫描信号则是由4-16线译码器74HC154来选择控制，这样一来列选控制只使用了单片机的4个IO口，节约了很多IO资源，为单片机系统扩充使用功能提供了条件。考虑到P0口必需设置上拉电阻，我们采用4.7 kΩ排电阻作为上拉电阻。
上传时间： 2013-10-16
上传用户：ywcftc277
家电制造业的竞争日益激烈，市场调整压力越来越大，原始设备制造商们（OEM）为了面对这一挑战，必须在满足电磁兼容性的条件下，不断降低产品的成本。由于强调成本控制，为防止由电源和信号线的瞬变所产生的电器故障而实施必要的瞬态免疫保护，对于家电设计者来说变得更具挑战性。由于传统的电源设计和电磁干扰（EMI）控制措施为节约成本让路，家电设计者必须开发出新的技术来满足不断调整的电磁兼容（EMC）需求。本应用笔记探讨了瞬态电气干扰对嵌入式微控制器（MCU）的影响，并提供了切实可行的硬件和软件设计技术，这些技术可以为电快速瞬变（EFT）、静电放电（ESD）以及其它电源线或信号线的短时瞬变提供低成本的保护措施。虽然这种探讨是主要针对家电制造商，但是也适用于消费电子、工业以及汽车电子方面的应用。 低成本的基于MCU 的嵌入式应用特别容易受到ESD 和EFT 影响降低性能。即使是运行在较低时钟频率下的微控制器，通常对快速上升时间瞬变也很敏感。这种敏感性归咎于所使用的工艺技术。如今针对低成本8/16位的MCU的半导体工艺技术所实现的晶体管栅极长度在0.65 μm～0.25 μm范围内。此范围内的栅极长度能产生和响应上升时间在次纳秒范围内（或超过300 MHz 的等同带宽）的信号。因此， MCU 能够响应进入其引脚的ESD 或EFT 信号。除上述工艺技术之外， MCU 在ESD 或EFT 事件中的性能还会受到IC 设计及其封装、印刷电路板（PCB）的设计、MCU 上运行的软件、系统设计以及ESD 或EFT 波形特征的影响。各因素的相对影响（强调对最大影响的贡献）如图1 所示。
上传时间： 2013-11-08
上传用户：Jerry_Chow
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
