Visual Basic Low Level Disk Acces
上传时间： 2013-12-23
上传用户：王楚楚
The STi7105 uses state of the art process technology to provide an ultra low-cost, fully featured HD AVC decoder IC. It is a highly integrated system-on-chip suitable for STB markets across all networks (cable/satellite/DTT/x- DSL/IP) worldwide
标签： technology low-cost featured process
上传时间： 2013-12-22
上传用户：时代电子小智
Buffer low THD distortion and hi-impendance, Very wide frequency band.
标签： hi-impendance distortion frequency Buffer
上传时间： 2014-08-08
上传用户：dragonhaixm
PXA270 design guide low level primitives
标签： primitives design guide level
上传时间： 2014-06-30
上传用户：yxgi5
Low density parity check matrix
标签： density parity matrix check
上传时间： 2014-01-08
上传用户：yt1993410
12bit 低功耗DAC 数模转换器 The MAX5302 combines a low-power, voltage-output, 12-bit digital-to-analog converter (DAC) and a precision output amplifier in an 8-pin µMAX package. It operates from a single +5V supply, drawing less than 280µA of supply current.
上传时间： 2017-02-21
上传用户：ckbihu
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上传时间： 2017-02-23
上传用户：w124141
The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal for self-powered and bus-powered Universal Serial Bus (USB) applications. Each switch has low on-resistance (110mΩ typical) and can supply 500mA minimum. The fault currents are limited to 1.0A typical and the flag output pin for each switch is available to indicate fault conditions to the USB controller. The thermal shutdown feature will prevent damage to the device when subjected to excessive current loads. The undervoltage lockout feature will ensure that the device will remain off unless there is a valid input voltage present.
标签： High-Side Switch Power Dual USB
上传时间： 2019-03-06
上传用户：bhitr
AEC-Q100 qualified • 12 V and 24 V battery systems compliance • 3.3 V and 5 V logic compatible I/O • 8-channel configurable MOSFET pre-driver – High-side (N-channel and P-channel MOS) – Low-side (N-channel MOS) – H-bridge (up to 2 H-bridge) – Peak & Hold (2 loads) • Operating battery supply voltage 3.8 V to 36 V • Operating VDD supply voltage 4.5 V to 5.5 V • All device pins, except the ground pins, withstand at least 40 V • Programmable gate charge/discharge currents for improving EMI behavior
标签： configurable Automotive pre-driver suitable channel systems MOSFET fully High side
上传时间： 2019-03-27
上传用户：guaixiaolong
The AZ1117 is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The AZ1117 series provides current limiting and thermal shutdown. Its circuit includes a trimmed bandgap reference to assure output voltage accuracy to be within 1% for 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5.0V and adjustable versions or 2% for 1.2V version. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal shutdown provides protection against any combination of overload and ambient temperature that would create excessive junction temperature. The AZ1117 has an adjustable version, that can provide the output voltage from 1.25V to 12V with only 2 external resistors.
上传时间： 2019-04-11
上传用户：heaven0o0o0
