Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with High-Side inductor current
上传时间： 2013-11-20
上传用户：stewart·
Traditionally, an Electronic Circuit Breaker (ECB) comprisesa MOSFET, a MOSFET controller and a current senseresistor. The LTC®4213 does away with the sense resistorby using the RDS(ON) of the external MOSFET. The resultis a simple, small solution that offers a signifi cant lowinsertion loss advantage at low operating load voltage.The LTC4213 features two circuit breaking responses tovarying overload conditions with three selectable tripthresholds and a high side drive for an external N-channelMOSFET switch.
上传时间： 2014-03-02
上传用户：lixinxiang
The LTC®4151 is a high side power monitor that includesa 12-bit ADC for measuring current and voltage, as wellas the voltage on an auxiliary input. Data is read throughthe widely used I2C interface. An unusual feature in thisdevice is its 7V to 80V operating range, allowing it to coverapplications from 12V automotive to 48V telecom.
上传时间： 2013-10-29
上传用户：集美慧
The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal for self-powered and bus-powered Universal Serial Bus (USB) applications. Each switch has low on-resistance (110mΩ typical) and can supply 500mA minimum. The fault currents are limited to 1.0A typical and the flag output pin for each switch is available to indicate fault conditions to the USB controller. The thermal shutdown feature will prevent damage to the device when subjected to excessive current loads. The undervoltage lockout feature will ensure that the device will remain off unless there is a valid input voltage present.
标签： High-Side Switch Power Dual USB
上传时间： 2019-03-06
上传用户：bhitr
The BTS5016SDA is a one channel High-Side power switch in PG-TO252-5-11 package providing embedded protective functions. The power transistor is built by a N-channel vertical power MOSFET with charge pump. The design is based on Smart SIPMOS chip on chip technology. The BTS5016SDA has a current controlled input and offers a diagnostic feedback with load current sense and a defined fault signal in case of overload operation, overtemperature shutdown and/or short circuit shutdown.
上传时间： 2019-03-27
上传用户：guaixiaolong
AEC-Q100 qualified • 12 V and 24 V battery systems compliance • 3.3 V and 5 V logic compatible I/O • 8-channel configurable MOSFET pre-driver – High-Side (N-channel and P-channel MOS) – Low-side (N-channel MOS) – H-bridge (up to 2 H-bridge) – Peak & Hold (2 loads) • Operating battery supply voltage 3.8 V to 36 V • Operating VDD supply voltage 4.5 V to 5.5 V • All device pins, except the ground pins, withstand at least 40 V • Programmable gate charge/discharge currents for improving EMI behavior
标签： configurable Automotive pre-driver suitable channel systems MOSFET fully High side
上传时间： 2019-03-27
上传用户：guaixiaolong
资料->【E】光盘论文->【E1】斯坦福博士论文->03 California PhD High integrity GPS-INS filter for precise relative navigation.pdf
标签： California navigation integrity relative
上传时间： 2013-07-03
上传用户：jiiszha
FPGA-based high-order FIR filter design
标签： FPGA-based high-order filter design
上传时间： 2013-08-06
上传用户：sssnaxie
Introduce High-Speed Digital System Design.
标签： High-Speed Digital Design System
上传时间： 2013-10-20
上传用户：gps6888
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
