Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
上海晶丰明源半导体有限公司(Bright Power Semiconductor ) 是一家从事电源管理芯片设计和销售的公司，公司主要产品是大功率LED驱动芯片.
上传时间： 2013-10-16
上传用户：aysyzxzm
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
This document presents design techniques and reference circuits that power Virtex™-4 FXRocketIO™ multi-gigabit transceivers (MGTs) operating at data rates below 3.125 Gb/s.When using multiple transceivers, it is sometimes preferred to power them from a switchingpower supply. However, switching power supplies generate noise that affects transceiver
上传时间： 2013-11-18
上传用户：huang111
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
Power over Ethernet (PoE) is a new development thatallows for the delivery of power to Ethernet-based devicesvia standard Ethernet CAT5 cable, precluding the need forwall adapters or other external power sources. The PoEspecification defines a hardware detection protocol wherePower Sourcing Equipment (PSE) is able to identify PoEPowered Devices (PDs), thus allowing full backwardscompatibility with non-PoE-aware (legacy) Ethernetdevices.
上传时间： 2013-11-11
上传用户：daoyue
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上传时间： 2013-10-23
上传用户：wuchunzhong
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
DC/DC 升压IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间： 2013-11-07
上传用户：3294322651
While simplicity and high effi ciency (for cool running) areno longer optional features in isolated power supplies, itis traditionally diffi cult to achieve both. Achieving higheffi ciency often requires the use of advanced topologiesand home-brewed secondary synchronous rectifi cationschemes once reserved only for higher power applications.This only adds to the parts count and to the designcomplexity associated with the reference and optocouplercircuits typically used to maintain isolation. Fortunately, abreakthrough IC makes it possible to achieve both high efficiency and simplicity in a synchronous fl yback topology.The LT®3825 simplifi es and improves the performance oflow voltage, high current fl yback supplies by providingprecise synchronous rectifi er timing and eliminating theneed for optocoupler feedback while maintaining excellentregulation and superior loop response.
上传时间： 2013-10-16
上传用户：wayne595
