Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上传时间： 2013-11-23
上传用户：rocketrevenge
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上传时间： 2013-11-12
上传用户：671145514
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签： Circuitry Operation Single 1017
上传时间： 2013-12-20
上传用户：Wwill
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
上传时间： 2014-12-23
上传用户：yl8908
摘要：从功率MOSFET内部结构和极间电容的电压依赖关系出发，对功率MOSFET的开关现象及其原因进行了较深入分析。从实际应用的角度，对功率MOSFET开关过程的功率损耗和所需驱动功率进行了研究，提出了有关参数的计算方法，并对多种因素对开关特性的影响效果进行了实验研究，所得出的结论对于功率MOSFET的正确运用和设计合理的MoSFET驱动电路具有指导意义．
上传时间： 2013-11-10
上传用户：wfeel
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上传时间： 2013-11-05
上传用户：AISINI005
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
标签： multiplexer reference VGA
上传时间： 2013-11-09
上传用户：ANRAN
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
印刷电路板（PCB）设计解决方案市场和技术领军企业Mentor Graphics（Mentor Graphics）宣布推出HyperLynx® PI（电源完整性）产品，满足业内高端设计者对于高性能电子产品的需求。HyperLynx PI产品不仅提供简单易学、操作便捷，又精确的分析，让团队成员能够设计可行的电源供应系统；同时缩短设计周期，减少原型生成、重复制造，也相应降低产品成本。随着当今各种高性能/高密度/高脚数集成电路的出现，传输系统的设计越来越需要工程师与布局设计人员的紧密合作，以确保能够透过众多PCB电源与接地结构，为IC提供纯净、充足的电力。配合先前推出的HyperLynx信号完整性（SI）分析和确认产品组件，Mentor Graphics目前为用户提供的高性能电子产品设计堪称业内最全面最具实用性的解决方案。“我们拥有非常高端的用户，受到高性能集成电路多重电压等级和电源要求的驱使，需要在一个单一的PCB中设计30余套电力供应结构。”Mentor Graphics副总裁兼系统设计事业部总经理Henry Potts表示。“上述结构的设计需要快速而准 确的直流压降(DC Power Drop)和电源杂讯(Power Noise)分析。拥有了精确的分析信息，电源与接地层结构和解藕电容数(de-coupling capacitor number)以及位置都可以决定，得以避免过于保守的设计和高昂的产品成本。”
上传时间： 2013-11-18
上传用户：362279997
