In this document, the term Ô60xÕ is used to denote a 32-bit microprocessor from the PowerPC architecture family that conforms to the bus interface of the PowerPC 601ª, PowerPC 603ª, or PowerPC 604 microprocessors. Note that this does not include the PowerPC 602ª microprocessor which has a multiplexed address/data bus. 60x processors implement the PowerPC architecture as it is speciÞed for 32-bit addressing, which provides 32-bit effective (logical) addresses, integer data types of 8, 16, and 32 bits,and ßoating-point data types of 32 and 64 bits (single-precision and double-precision).1.1 Overview The MPC106 provides an integrated high-bandwidth, high-performance, TTL-compatible interface between a 60x processor, a secondary (L2) cache or additional (up to four total) 60x processors, the PCI bus,and main memory. This section provides a block diagram showing the major functional units of the 106 and describes brießy how those units interact.Figure 1 shows the major functional units within the 106. Note that this is a conceptual block diagram intended to show the basic features rather than an attempt to show how these features are physically implemented on the device.
上传时间： 2013-10-08
上传用户：18711024007
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
上传时间： 2013-11-04
上传用户：as275944189
//遥控解码子程序，LC7461，用户码为11C//external interrupt0void isr_4(){ unsigned char r_count;//定义解码的个数 unsigned long use_data=0;//定义16位的用户码，只用到13位 unsigned long use_code=0;//定义16位的用户反码，只用到13位 unsigned long data=0;//定义16位数据码，包括8位数据码和反码 unsigned char data_h=0;//数据反码 unsigned char data_l=0;//数据码 _clrwdt();// _delay(7000);//7461解码，延时7000// _delay(7000);//7461解码，延时7000//_delay(7000);//7461解码，延时7000 if(remote==1) goto error; while(remote==0);//wait to high //_delay(9744);count_delay=0; while(count_delay<143); if(remote==1) goto error; /////用户码解码use_data//////////add////////////////////////// for(r_count=13;r_count>0;r_count--) { while(remote==0);//wait to high count_delay=0; while(count_delay<24);//_delay(1680); _c=remote; if(_c==1) { _lrrc(&use_data); count_delay=0; while(count_delay<32);//_delay(2200);//wait to low } else _lrrc(&use_data); } _nop(); //if(remote==1) //_delay(1680);//wait to low while(remote==1);//wait to low _nop(); ////////用户码解码finish/////////add/////////add//////// /////用户码反码解码use_code//////////add////////////////////////// for(r_count=13;r_count>0;r_count--) { while(remote==0);//wait to high count_delay=0; while(count_delay<24);//_delay(1680); _c=remote; if(_c==1) { _lrrc(&use_code); count_delay=0; while(count_delay<32);//_delay(2200);//wait to low } else _lrrc(&use_code); } _nop(); //if(remote==1) // _delay(1680);//wait to low while(remote==1);//wait to low _nop(); ////////用户码反码解码finish/////////add/////////add//////// ////数据码解码开始////data_l为用户码，data_h为数据码反码//////////// for(r_count=16;r_count>0;r_count--) { while(remote==0);//wait to high count_delay=0; while(count_delay<24);//_delay(1680); _c=remote; if(_c==1) { _lrrc(&data); count_delay=0; while(count_delay<32);//_delay(2200);//wait to low } else _lrrc(&data); } ////数据码解码结束//////////////////////////////////////////////// data_l=data; data_h=data>>8; ///用户码////// use_data>>=3; use_code>>=3; use_code=~use_code; //////// ////如果用户码等与0x11c并且数据码和数据反码都校验一致，解码成功 //if((~data_h==data_l)&&use_data==0x11c)//使用用户码 //跳过用户码 if(~data_h==data_l)//如果数据码和数据反码（取反后）相等，解码正确 { _nop(); r_data=data_l;//r_data为解出的最终数据码 } //否则解码不成功 _nop(); _nop();error: //r_data=nocode; _nop(); _nop(); _nop();}
上传时间： 2014-03-27
上传用户：shenlan
16 16点阵显示汉字原理及显示程序 #include "config.h" #define DOTLED_LINE_PORT PORTB #define DOTLED_LINE_DDR DDRB #define DOTLED_LINE_PIN PINB #define DOTLED_LINE_SCKT PB1 #define DOTLED_LINE_SCKH PB5 #define DOTLED_LINE_SDA PB3 #define DOTLED_ROW_PORT PORTC #define DOTLED_ROW_DDR DDRC #define DOTLED_ROW_PIN PINC #define DOTLED_ROW_A0 PC0 #define DOTLED_ROW_A1 PC1 #define DOTLED_ROW_A2 PC2 #define DOTLED_ROW_A3 PC3 #define DOTLED_ROW_E PC4 uint8 font[] = { /*-- 调入了一幅图像：这是您新建的图像 --*/ /*-- 宽度x高度=16x16 --*/ 0x00,0x00,0x00,0x00,0x08,0x38,0x18,0x44,0x08,0x44,0x08,0x04,0x08,0x08,0x08,0x10, 0x08,0x20,0x08,0x40,0x08,0x40,0x08,0x40,0x3E,0x7C,0x00,0x00,0x00,0x00,0x00,0x00 }; static void TransmitByte(uint8 byte); static void SelectRow(uint8 row); static void FlipLatchLine(void); static void TransmitByte(uint8 byte) { uint8 i; for(i = 0 ; i < 8 ; i ++) { if(byte & (1 << i)) { DOTLED_LINE_PORT |= _BV(DOTLED_LINE_SDA); } else { DOTLED_LINE_PORT &= ~_BV(DOTLED_LINE_SDA); } //__delay_cycles(100); DOTLED_LINE_PORT |= _BV(DOTLED_LINE_SCKH); //__delay_cycles(100); DOTLED_LINE_PORT &= ~_BV(DOTLED_LINE_SCKH); //__delay_cycles(100); } } static void SelectRow(uint8 row) { //row -= 1; row |= DOTLED_ROW_PIN & 0xe0; DOTLED_ROW_PORT = row; } static void FlipLatchLine(void) { DOTLED_LINE_PORT |= _BV(DOTLED_LINE_SCKT); DOTLED_LINE_PORT &= ~_BV(DOTLED_LINE_SCKT); } void InitDotLedPort(void) { DOTLED_LINE_PORT &= ~(_BV(DOTLED_LINE_SCKT) | _BV(DOTLED_LINE_SCKH)); DOTLED_LINE_PORT |= _BV(DOTLED_LINE_SDA); DOTLED_LINE_DDR |= _BV(DOTLED_LINE_SCKT) | _BV(DOTLED_LINE_SCKH) | _BV(DOTLED_LINE_SDA); DOTLED_ROW_PORT |= 0x1f; DOTLED_ROW_PORT &= 0xf0; DOTLED_ROW_DDR |= 0x1f; } void EnableRow(boolean IsEnable) { if(IsEnable) { DOTLED_ROW_PORT &= ~_BV(DOTLED_ROW_E); } else { DOTLED_ROW_PORT |= _BV(DOTLED_ROW_E); } } void PrintDotLed(uint8 * buffer) { uint8 i , tmp; for(i = 0 ; i < 16 ; i ++) { tmp = *buffer ++; TransmitByte(~tmp); tmp = *buffer ++; TransmitByte(~tmp); SelectRow(i); FlipLatchLine(); } } void main(void) { InitDotLedPort(); EnableRow(TRUE); while(1) { PrintDotLed(font); __delay_cycles(5000); } } //---------------------------------------------------- config.h文件 #ifndef _CONFIG_H #define _CONFIG_H //#define GCCAVR #define CPU_CYCLES 7372800L #ifndef GCCAVR #define _BV(bit) (1 << (bit)) #endif #define MSB 0x80 #define LSB 0x01 #define FALSE 0 #define TRUE 1 typedef unsigned char uint8; typedef unsigned int uint16; typedef unsigned long uint32; typedef unsigned char boolean; #include <ioavr.h> #include <inavr.h> #include "dotled.h" #endif //-----
上传时间： 2013-11-18
上传用户：mnacyf
There has long been a need for portable ultrasoundsystems that have good resolution at affordable costpoints. Portable systems enable healthcare providersto use ultrasound in remote locations such asdisaster zones, developing regions, and battlefields,where it was not previously practical to do so.
上传时间： 2013-10-26
上传用户：liulinshan2010
很多不同的厂家生产各种型号的计算机，它们运行完全不同的操作系统，但TCP.IP协议族允许它们互相进行通信。这一点很让人感到吃惊，因为它的作用已远远超出了起初的设想。T C P / I P起源于6 0年代末美国政府资助的一个分组交换网络研究项目，到9 0年代已发展成为计算机之间最常应用的组网形式。它是一个真正的开放系统，因为协议族的定义及其多种实现可以不用花钱或花很少的钱就可以公开地得到。它成为被称作“全球互联网”或“因特网(Internet)”的基础，该广域网（WA N）已包含超过1 0 0万台遍布世界各地的计算机。本章主要对T C P / I P协议族进行概述，其目的是为本书其余章节提供充分的背景知识。 TCP.IP协议 缩略语 ACK (ACKnowledgment) TCP首部中的确认标志 API (Application Programming Interface) 应用编程接口 ARP (Address Resolution Protocol) 地址解析协议 ARPANET(Defense Advanced Research Project Agency NETwork) (美国)国防部远景研究规划局 AS (Autonomous System) 自治系统 ASCII (American Standard Code for Information Interchange) 美国信息交换标准码 ASN.1 (Abstract Syntax Notation One) 抽象语法记法1 BER (Basic Encoding Rule) 基本编码规则 BGP (Border Gateway Protocol) 边界网关协议 BIND (Berkeley Internet Name Domain) 伯克利I n t e r n e t域名 BOOTP (BOOTstrap Protocol) 引导程序协议 BPF (BSD Packet Filter) BSD 分组过滤器 CIDR (Classless InterDomain Routing) 无类型域间选路 CIX (Commercial Internet Exchange) 商业互联网交换 CLNP (ConnectionLess Network Protocol) 无连接网络协议 CRC (Cyclic Redundancy Check) 循环冗余检验 CSLIP (Compressed SLIP) 压缩的S L I P CSMA (Carrier Sense Multiple Access) 载波侦听多路存取 DCE (Data Circuit-terminating Equipment) 数据电路端接设备 DDN (Defense Data Network) 国防数据网 DF (Don’t Fragment) IP首部中的不分片标志 DHCP (Dynamic Host Configuration Protocol) 动态主机配置协议 DLPI (Data Link Provider Interface) 数据链路提供者接口 DNS (Domain Name System) 域名系统 DSAP (Destination Service Access Point) 目的服务访问点 DSLAM (DSL Access Multiplexer) 数字用户线接入复用器 DSSS (Direct Sequence Spread Spectrum) 直接序列扩频 DTS (Distributed Time Service) 分布式时间服务 DVMRP (Distance Vector Multicast Routing Protocol) 距离向量多播选路协议 EBONE (European IP BackbONE) 欧洲I P主干网 EOL (End of Option List) 选项清单结束 EGP (External Gateway Protocol) 外部网关协议 EIA (Electronic Industries Association) 美国电子工业协会 FCS (Frame Check Sequence) 帧检验序列 FDDI (Fiber Distributed Data Interface) 光纤分布式数据接口 FIFO (First In, First Out) 先进先出 FIN (FINish) TCP首部中的结束标志 FQDN (Full Qualified Domain Name) 完全合格的域名 FTP (File Transfer Protocol) 文件传送协议 HDLC (High-level Data Link Control) 高级数据链路控制 HELLO 选路协议 IAB (Internet Architecture Board) Internet体系结构委员会 IANA (Internet Assigned Numbers Authority) Internet号分配机构 ICMP (Internet Control Message Protocol) Internet控制报文协议 IDRP (InterDomain Routing Protocol) 域间选路协议 IEEE (Institute of Electrical and Electronics Engineering) （美国）电气与电子工程师协会 IEN (Internet Experiment Notes) 互联网试验注释 IESG (Internet Engineering Steering Group) Internet工程指导小组 IETF (Internet Engineering Task Force) Internet工程专门小组 IGMP (Internet Group Management Protocol) Internet组管理协议 IGP (Interior Gateway Protocol) 内部网关协议 IMAP (Internet Message Access Protocol) Internet报文存取协议 IP (Internet Protocol) 网际协议 I RTF (Internet Research Task Force) Internet研究专门小组 IS-IS (Intermediate System to Intermediate System Protocol) 中间系统到中间系统协议 ISN (Initial Sequence Number) 初始序号 ISO (International Organization for Standardization) 国际标准化组织 ISOC (Internet SOCiety) Internet协会 LAN (Local Area Network) 局域网 LBX (Low Bandwidth X) 低带宽X LCP (Link Control Protocol) 链路控制协议 LFN (Long Fat Net) 长肥网络 LIFO (Last In, First Out) 后进先出 LLC (Logical Link Control) 逻辑链路控制 LSRR (Loose Source and Record Route) 宽松的源站及记录路由 MBONE (Multicast Backbone On the InterNEt) Internet上的多播主干网 MIB (Management Information Base) 管理信息库 MILNET (MILitary NETwork) 军用网 MIME (Multipurpose Internet Mail Extensions) 通用I n t e r n e t邮件扩充 MSL (Maximum Segment Lifetime) 报文段最大生存时间 MSS (Maximum Segment Size) 最大报文段长度 M TA (Message Transfer Agent) 报文传送代理 MTU (Maximum Transmission Unit) 最大传输单元 NCP (Network Control Protocol) 网络控制协议 NFS (Network File System) 网络文件系统 NIC (Network Information Center) 网络信息中心 NIT (Network Interface Tap) 网络接口栓（S u n公司的一个程序） NNTP (Network News Transfer Protocol) 网络新闻传送协议 NOAO (National Optical Astronomy Observatories) 国家光学天文台 NOP (No Operation) 无操作 NSFNET (National Science Foundation NETwork) 国家科学基金网络 NSI (NASA Science Internet) （美国）国家宇航局I n t e r n e t NTP (Network Time Protocol) 网络时间协议 NVT (Network Virtual Terminal) 网络虚拟终端 OSF (Open Software Foudation) 开放软件基金 OSI (Open Systems Interconnection) 开放系统互连 OSPF (Open Shortest Path First) 开放最短通路优先 PAWS (Protection Against Wrapped Sequence number) 防止回绕的序号 PDU (Protocol Data Unit) 协议数据单元 POSIX (Portable Operating System Interface) 可移植操作系统接口 PPP (Point-to-Point Protocol) 点对点协议 PSH (PuSH) TCP首部中的急迫标志 RARP (Reverse Address Resolution Protocol) 逆地址解析协议 RFC (Request For Comments) Internet的文档，其中的少部分成为标准文档 RIP (Routing Information Protocol) 路由信息协议 RPC (Remote Procedure Call) 远程过程调用 RR (Resource Record) 资源记录 RST (ReSeT) TCP首部中的复位标志 RTO (Retransmission Time Out) 重传超时 RTT (Round-Trip Time) 往返时间 SACK (Selective ACKnowledgment) 有选择的确认 SLIP (Serial Line Internet Protocol) 串行线路I n t e r n e t协议 SMI (Structure of Management Information) 管理信息结构 SMTP (Simple Mail Transfer Protocol) 简单邮件传送协议 SNMP (Simple Network Management Protocol) 简单网络管理协议 SSAP (Source Service Access Point) 源服务访问点 SSRR (Strict Source and Record Route) 严格的源站及记录路由 SWS (Silly Window Syndrome) 糊涂窗口综合症 SYN (SYNchronous) TCP首部中的同步序号标志 TCP (Transmission Control Protocol) 传输控制协议 TFTP (Trivial File Transfer Protocol) 简单文件传送协议 TLI (Transport Layer Interface) 运输层接口 TTL (Ti m e - To-Live) 生存时间或寿命 TUBA (TCP and UDP with Bigger Addresses) 具有更长地址的T C P和U D P Telnet 远程终端协议 UA (User Agent) 用户代理 UDP (User Datagram Protocol) 用户数据报协议 URG (URGent) TCP首部中的紧急指针标志 UTC (Coordinated Universal Time) 协调的统一时间 UUCP (Unix-to-Unix CoPy) Unix到U n i x的复制 WAN (Wide Area Network) 广域网 WWW (World Wide Web) 万维网 XDR (eXternal Data Representation) 外部数据表示 XID (transaction ID) 事务标识符 XTI (X/Open Transport Layer Interface) X/ O p e n运输层接口
上传时间： 2013-11-13
上传用户：tdyoung
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
上传时间： 2013-10-23
上传用户：685
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
标签： 无线技术
上传时间： 2013-10-08
上传用户：kinochen
1.1 我如何决定使用那种整数类型？ 如果需要大数值(大于32, 767 或小于¡32, 767), 使用long 型。否则, 如果空间很重要(如有大数组或很多结构), 使用short 型。除此之外, 就使用int 型。如果严格定义的溢出特征很重要而负值无关紧要, 或者你希望在操作二进制位和字节时避免符号扩展的问题, 请使用对应的无符号类型。但是, 要注意在表达式中混用有符号和无符号值的情况。
上传时间： 2013-11-22
上传用户：ming529
