如果在调谐器或电视机附近使用本机或任何其他使用微处理器的电子设备，则可能会产生图像的噪声或干扰。如果发生这种情况，请采取以下步骤将本机安装在尽可能远离调谐器或T的地方。远离调谐器或T，远离本机的电源线和输入/输出连接电缆。尤其在使用室内天线或300欧姆馈线。我们建议使用室外天线和75 Q / ohm同轴电缆Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV If this happens, take the following stepsInstall this unit as far away as possible from the tuner or T Run the antenna wires from the tuner or T away from this unit ' s power supply cord and input/output connection cables. Noise or disturbance tends to occur particularly when using indoor antennas or300 ohm feeder wires. We recommend using outdoor antennas and 75 Q/ohm coaxial cables
标签： 功放
上传时间： 2022-04-22
上传用户：
ATS2819/ATS2819P标准应用方案主要分为以下功能模块：Power Supply，BlueTooth，Audio Input/Output（包括codec、I2C、SPDIF），FM Receiver，disaplay（LED&LCD），USB，SPI NOR Flash Memory，SD/MMC/MS Card等。1.2原理图设计总体原则1原理图设计需要按照方案规格的要求实现各项硬件功能，尽量避免功能模块相互间的资源冲突。如果存在I/O复用，接收复用等情况，除了需注意检查I/O上电状态，接口时序等，还需要注意复用的SIO工作频率与工作电压域是否符合要求(如WIO)，确保功能设计正确实现。2原理图设计要求性能达到要求。如稳定性，启动电压，功耗，ESD，EMI等。要注意检查模块电源开关状态，选择的原件标称及精度、材质，接口保护元件和EMI滤波器等。3系统时钟26MHZ，要求CL为7~9PF，精度为+-10PPM。这样才能保证系统能正常工作。4当设计PCB受限于模具大小时，各个模块无法保证均能得到最优的布局布线(如滤波电容要求靠近IC、走线上要求尽量少的过孔与尽可能短的走线)。因为在此给出一个模块优先级以供设计人员参考，从而提高方案设计的效率，增加一版work的可行性。将优先级以阿拉伯数据排列
上传时间： 2022-06-07
上传用户：
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
标签： MAXREFDES Lakewood Isolated Output
上传时间： 2013-11-02
上传用户：fengzimili
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
标签： Riverside MAXREFDES Isolated Output
上传时间： 2013-11-16
上传用户：会稽剑客
verilog编写的状态机检测00100序列. 实现 input:...011000010010000... output:...000000000100100... 并且 用测试模块来验证状态是否正确工作
标签： 000000000100100 011000010010000 verilog output
上传时间： 2015-07-14
上传用户：ggwz258
realize overlapped-add method ％[y]=overlpadd(x,h,Nfft) ％y:output sequence ％x:input sequence ％h:filter impulse response sequence ％Nfft:points of each DFT operation ％重叠相加法实现分段卷积
标签： sequence overlapped-add overlpadd realize
上传时间： 2015-07-22
上传用户：as275944189
％realize overlapped-save method ％y:output sequence ％x:input seqence ％h:filter impulse response sequence ％N:length of each segment ％重叠保留法实现分段卷积
标签： overlapped-save sequence response realize
上传时间： 2015-07-22
上传用户：chenbhdt
Second and Higher-Order Statistics based Multiple-Input-Multiple-Output System Blind Identification Matlab Code
标签： Multiple-Input-Multiple-Output Identification Higher-Order Statistics
上传时间： 2013-12-24
上传用户：wpt
Soft Input Soft Output Viterbi Algorithm
标签： Soft Algorithm Viterbi Output
上传时间： 2013-12-27
上传用户：yoleeson
by Jay Kadane。Input:a vector with floats.Output:the maximum submatrix.
标签： submatrix maximum Kadane Output
上传时间： 2015-10-13
上传用户：彭玖华
