基于FPGA设计的相关论文资料大全 84篇用FPGA实现FFT的研究 刘朝晖 韩月秋 摘 要 目的 针对高速数字信号处理的要求，给出了用现场可编程门阵列(FPGA)实现的 快速傅里叶变换(FFT)方案.方法 算法为按时间抽取的基4算法，采用递归结构的块浮点运 算方案，蝶算过程只扩展两个符号位以适应雷达信号处理的特点，乘法器由阵列乘法器实 现.结果 采用流水方式保证系统的速度，使取数据、计算旋转因子、复乘、DFT等操作协 调一致，在计算、通信和存储间取得平衡，避免了瓶颈的出现.结论 实验表明，用FPGA 实现高速数字信号处理的算法是一个可行的方案. 关键词 离散傅里叶变换； 快速傅里叶变换； 块浮点运算； 可编程门阵列 分类号 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the requirement for high speed digital signal processing. Methods The structure of FPGA and requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
标签： fpga
上传时间： 2022-03-23
上传用户：
本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
以AT89S52单片机为控制核心,采用电容降压技术,Buck电路拓扑,PWM驱动模块和功率器件散热设计,通过高速的数据采集、主功率输入输出模块和控制模块,设计一种新型智能车载充电器.在充电过程中,通过负脉冲瞬间放电实现对铅酸蓄电池的再生修复,提高电池的有效容量,延长使用寿命.该充电器体积小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat dissipation design,through high-speed data acquisition,main power input and output module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast speed,high efficiency and good reliability.
标签： 车载充电器
上传时间： 2022-03-27
上传用户：
在半导体制冷技术的工作性能及其优缺点研究的基础上,设计了以单片机为核心控制元件,以TEC1-12706为执行元件的半导体制冷温度控制系统。采用高精度分段式PID控制算法配合PWM输出控制的方法实现温度控制;选择数字传感器DS18B20为温度检测元件,还包含1602液晶显示模块、按键调整输入模块和H桥驱动模块等。实际测试表明,该系统结构简单易行,操作方便,工作性能优良,同时针对该系统专门设计的温控算法,使半导体制冷器能更好地适应不同工况而充分发挥其制冷制热工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM output control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test shows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.
上传时间： 2022-03-27
上传用户：
温度控制如今已成为当代社会研究的热点之一,而温度检测在现代设备参数检测中也是一项极其重要的技术,应用十分广泛。与传统的测温方法相比,红外测温方法具有时间短、精度高、使用简单方便等优点。本文以环境温度为被测对象,设计了以STC89C52单片机为控制中心的红外测温装置,能够实现对目标温度的实时采集、处理、显示和报警等功能。本设计主要是由STC89C52单片机、红外测温传感器、LCD1602液晶显示器、按键和蜂鸣器等部分组成,采用非接触的方式对目标温度进行实时检测。Temperature control has become one of the hotspots in contemporary social research,and temperature detection is an extremely important technology in modern equipment parameter detection.Compared with traditional method,the infrared temperature measuring method has advantages of short time,high precision and convenient operation,etc.This paper consider environment temperature as research objects and designs an infrared temperature measuring device which employs the STC89C52singlechipas-control center,and it can realize timely collection,processing,display and alarm function of the target temperature.The design is mainly composed of STC89C52 singlechip,infrared temperature sensor,LCD1602monitor,keys and buzzer,etc.This design detects the target temperature by non-contact method.
上传时间： 2022-03-27
上传用户：jiabin
CAN总线是汽车上应用最广泛的车载网络总线,具有实时性强、可靠性高、成本低等优点。鉴于此,介绍了一种利用飞思卡尔系列单片机MC9S12XS128作为控制器,利用其内部的MSCAN模块、CAN收发器TJA1040等外围元件进行CAN总线通信节点设计。该设计能够实现CAN总线数据的发送与接收,可应用于汽车及其他各种CAN总线通信系统。CAN bus is the most widely used on-board network bus in automobiles. It has the advantages of realtime, high reliability and low cost. In view of this,this paper introduces the design of CAN bus communication node by using Freescale MC9S12XS128 as controller,using its internal MSCAN module,CAN transceiver TJA1040 and other peripheral components. This design can realize the sending and receiving of CAN bus data,and can be used in automobile and other CAN bus communication systems.
上传时间： 2022-03-27
上传用户：
文章提出了一种基于AT89S51单片机的智能家居系统的设计,该系统具有室内煤气以及烟雾的检测、家庭室内防盗等功能。文章详细分析了系统的总体设计,详尽分析并设计了煤气传感器模块、烟雾传感器模块、人体红外感应传感器模块、报警模块等各硬件部分,并利用PROTUES软件进行了系统仿真。仿真结果证明:系统具有成本低、效率高、操作方便等优点,达到了预期设计的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上传时间： 2022-03-28
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal processing(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
本文首次设计并验证了基于macom三合一芯片设计的光模块电路,该电路旨在提供一种满足SFF-8472中规定的数字诊断功能的低成本SFP+模块。电路采用激光器驱动、限幅放大器、控制器以及时钟恢复单元集成的单芯片,在保证高精度数字诊断功能基础上,实现了低成本高可靠的特点。该电路在光接收接口组件与激光器驱动和限幅放大器单元的限幅放大器部分之间接入滤波器来提高模块的灵敏度及信号质量。在控制器单元的数字电位器的引脚上采用外加电阻的方式避免出现上电不发光的故障问题。该研究结果为下一代SFP-DD光模块设计与开发工作,奠定了一定的理论与实践基础。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
上传时间： 2022-04-03
上传用户：
