利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
Designing read/write device (RWD) units for industrial RF-Identification applications is strongly facilitated by the NXP Semiconductors HITAG Reader Chip HTRC110. All needed function blocks, like the antenna driver, modulator demodulator and antenna diagnosis unit, are integrated in the HTRC110. Therefore only a minimum number of additional passive components are required for a complete RWD. This Application Note describes how to design an industrial RF-Identification system with the HTRC110. The major focus is dimensioning of the antenna, all other external components including clock and power supply, as well as the demodulation principle and its implementatio
上传时间： 2013-10-22
上传用户：zhengjian
常用PIC系列产品特性一览表 器件 存储器 类型 字数 EEPROM 数据 存储器 RAM I/O 引脚数 ADC （-Bit） 比较 器 运 放 定时器/WDT 串行接口 最高 速度 MHz 封装 PDIP /SOIC ICSP CCP / ECCP 输出电流 (per I/O) 振荡器 频率 (MHz) 参考 电压 VREF LCD PWM 堆栈 深度 High Voltage Wakeup On Change PIC16C432 OTP 2048x14 128 12 2 1-8bit/1-WDT 20 20 √ 25 mA 4 0 0 PIC16C433 OTP 2048x14 128 6 4/8 1-8bit/1-WDT 10 18 √ 25 mA 0 0 PIC16C505 OTP 1024x12 72 12 1-8bit/1-WDT 20 14 √ 25 mA 4 0 0 PIC16C54 OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54A OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54C OTP 512x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C55 OTP 512x12 24 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C554 OTP 512x14 80 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C558 OTP 2048x14 128 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C55A OTP 512x12 24 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C56 OTP 1024x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C56A OTP 1024x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C57 OTP 2048x12 72 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C57C OTP 2048x12 72 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C58B OTP 2048x12 73 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C620 OTP 512x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C620A OTP 512x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C621 OTP 1024x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C621A OTP 1024x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C622 OTP 2048x14 128 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C622A OTP 2048x14 128 13 2 1-8bit/1-WDT 40 18/20/40 √ 25 mA √ 0 0 PIC16C62A OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C/ SPI 20 28/ √ 1 25 mA 1 0 0 PIC16C62B OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C /SPI 20 28 √ 1 25 mA 1 0 0 PIC16C63 OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 28 √ 2 25 mA 2 0 0 PIC16C63A OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C642 OTP 4096x14 176 22 2 1-8bit/1-WDT 20 28 √ 25 mA √ 0 0 PIC16C64A OTP 2048x14 128 33 2-8bit/1-16bit/1-WDT I²C /SPI 20 40/44 √ 1 25 mA 1 0 0 PIC16C65A OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C65B OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C66 OTP 8192x14 368 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C662 OTP 4096x14 176 33 2 1-8bit/1-WDT 20 40/44 √ 25 mA √ 0 0 PIC16C67 OTP 8192x14 368 33 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C71 OTP 1024x14 36 13 4/8 1-8bit/1-WDT 20 18 √ 25 mA 0 0 PIC16C710 OTP 512x14 36 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C711 OTP 1024x14 68 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA
上传时间： 2013-10-12
上传用户：xjy441694216
为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
现有基于MAX7219芯片的数码管驱动电路只适用于小尺寸LED，为扩展其使用范围，在介绍动态显示芯片MAX7219功能的基础上，提出了一个基于该芯片的8位高亮度8英寸数码管驱动电路。电路保留了MAX7219芯片的功能强大、编程简单等优点，通过74LS273锁存器和ULN2803达林顿驱动器，实现了对任意大尺寸数码管提供较高电压和电流驱动的静态显示，并亮度可调。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
上传时间： 2013-10-23
上传用户：31633073
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
为解决当前计算机串行通讯接口只有USB，难以满足旧型号设备或某些单片机要求RS232通讯的问题，设计出两款RS232/USB电路。采用CH341A与MAX223集成电路芯片构建标准9线RS232/USB通用接口转换器，无需编程。采用CH341A与PIC16F877A构建单片机与计算机之间的USB通讯电路，软件遵循RS232通讯协议，硬件进行电平转换。实际使用表明，这两款产品与计算机端Windows 操作系统下的串口应用程序完全兼容，且通讯过程中无握手失败现象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上传时间： 2013-11-03
上传用户：siying
，我说说AVR 的集成开发环境。也就是常说的IDE（Integrated Development Environment）。图片比较多，虽然用软件处理过体积，网页可能还是比较慢，还请见谅。 现今世界上的AVR 开发环境可以说是百花齐放了，互相当然各有长短，我们看看都有哪些： 首当其冲的应该还是IAR，为什么呢，因为当初AVR 还在ATMEL 胎中酝酿的时候，IAR 公司 参与了AVR 的设计，因此可以认为IAR 有更为正统的血液，它最了解AVR，它的编译器编出来的 代码应该最优秀。好比你生的孩子还是你最了解——至少相当长一段时间是这样的。事实上，IAR for AVR 确实展现了这个实力，它的功能确实最为强大，无论是源代码编写还是软件乃至硬件仿 真，编译出来的代码也十分优秀。但是事物总是相对存在的，优点有时就意味着缺点。IAR 功能 全面而强悍，代价就是它的软件界面比较复杂，设置选项多，网上的资料也比较少，最要命的是 这个软件非常的贵，好吧你说你有破解版，但是破解文件一般并不通用，而且破解方法一般都稍 显繁琐。以上几条，对于新接触AVR 的人来说，几乎是迈不过的坎。
标签： AVR
上传时间： 2013-10-15
上传用户：weiwolkt
设计一种基于P89V51RD2的功率因数测量仪，采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心，大大简化系统硬件设计。而软件部分采用模块化设计思想，采用中值滤波和小数补偿算法，实现功率因数的高精度测量。实验测试表明，该功率因数测量仪测量精度高，运行稳定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上传时间： 2014-12-27
上传用户：CHINA526
针对目前汽车追尾事件频发问题，提出一种防汽车车前和车后追尾的安全装置设计。该设计以高性能、低功耗的8位AVR微处理器ATmega8L为核心，结合霍尔式车速传感器、激光雷达测距装置和MMA7260QT加速度传感器，能够兼顾车前和车后，摒弃以往设计中只考虑车前或车后单一性缺点，尤其适用于高速、夜晚或新手行车。 Abstract: Aiming at the high frequency of vehicle rear-end collision，a safe device design of anti-vehicle rear-end collision is presented.In the design，the high-performance，low-power8-bit AVR microprocessor ATmega8L is utilized as a core combined with Hall-type speed sensor，laser-radar ranging devices and the acceleration sensor MMA7260QT.The design considers both the front and back of a car，and overcomes the drawbacks of former designs in which only the front or the back of the car is considered，so it is especially suitable for high-speed，night or the beginner’s driving.
上传时间： 2013-10-14
上传用户：GavinNeko
