HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
常用PIC系列产品特性一览表 器件 存储器 类型 字数 EEPROM 数据 存储器 RAM I/O 引脚数 ADC （-Bit） 比较 器 运 放 定时器/WDT 串行接口 最高 速度 MHz 封装 PDIP /SOIC ICSP CCP / ECCP 输出电流 (per I/O) 振荡器 频率 (MHz) 参考 电压 VREF LCD PWM 堆栈 深度 High Voltage Wakeup On Change PIC16C432 OTP 2048x14 128 12 2 1-8bit/1-WDT 20 20 √ 25 mA 4 0 0 PIC16C433 OTP 2048x14 128 6 4/8 1-8bit/1-WDT 10 18 √ 25 mA 0 0 PIC16C505 OTP 1024x12 72 12 1-8bit/1-WDT 20 14 √ 25 mA 4 0 0 PIC16C54 OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54A OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54C OTP 512x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C55 OTP 512x12 24 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C554 OTP 512x14 80 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C558 OTP 2048x14 128 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C55A OTP 512x12 24 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C56 OTP 1024x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C56A OTP 1024x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C57 OTP 2048x12 72 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C57C OTP 2048x12 72 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C58B OTP 2048x12 73 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C620 OTP 512x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C620A OTP 512x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C621 OTP 1024x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C621A OTP 1024x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C622 OTP 2048x14 128 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C622A OTP 2048x14 128 13 2 1-8bit/1-WDT 40 18/20/40 √ 25 mA √ 0 0 PIC16C62A OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C/ SPI 20 28/ √ 1 25 mA 1 0 0 PIC16C62B OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C /SPI 20 28 √ 1 25 mA 1 0 0 PIC16C63 OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 28 √ 2 25 mA 2 0 0 PIC16C63A OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C642 OTP 4096x14 176 22 2 1-8bit/1-WDT 20 28 √ 25 mA √ 0 0 PIC16C64A OTP 2048x14 128 33 2-8bit/1-16bit/1-WDT I²C /SPI 20 40/44 √ 1 25 mA 1 0 0 PIC16C65A OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C65B OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C66 OTP 8192x14 368 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C662 OTP 4096x14 176 33 2 1-8bit/1-WDT 20 40/44 √ 25 mA √ 0 0 PIC16C67 OTP 8192x14 368 33 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C71 OTP 1024x14 36 13 4/8 1-8bit/1-WDT 20 18 √ 25 mA 0 0 PIC16C710 OTP 512x14 36 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C711 OTP 1024x14 68 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA
上传时间： 2013-10-12
上传用户：xjy441694216
为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
现有基于MAX7219芯片的数码管驱动电路只适用于小尺寸LED，为扩展其使用范围，在介绍动态显示芯片MAX7219功能的基础上，提出了一个基于该芯片的8位高亮度8英寸数码管驱动电路。电路保留了MAX7219芯片的功能强大、编程简单等优点，通过74LS273锁存器和ULN2803达林顿驱动器，实现了对任意大尺寸数码管提供较高电压和电流驱动的静态显示，并亮度可调。 Abstract: The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.
上传时间： 2013-10-23
上传用户：31633073
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
在航电系统维护过程中，为解决定位故障的效率和降低维修成本等问题，提出了基于ICD（Interface Control Document，接口控制文件）的1553B总线的信息监控系统模型。该系统运用数据采集卡对总线中传输的信号有无失真、偏差等电气特性进行检测，并使用1553B通讯卡通过测控软件LabWindows/CVI编程与ICD数据库的动态链接，实现总线信息的解析和故障的判断。与传统的维护过程相比，这种模型能够从信号的电气特性以及信息的解析等全方位的去检测判断故障的来源，并且能够广泛在其他1553B总线系统内扩展应用。验证表明该监控系统可以对总线信息进行快速有效地监测分析，能满足应用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
上传时间： 2013-11-23
上传用户：18752787361
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
为提高太阳能的利用率，以ATmega8单片机为控制核心，设计了一套光电跟踪与视日运动轨迹跟踪互补控制的双轴太阳跟踪器。该跟踪器在晴天时，利用光敏电阻采集光强判断太阳位置,控制步进电机实现光电跟踪；在阴天时，采集时钟器件PCF8583的时间信息,计算当前太阳位置来实现视日运动轨迹跟踪。实验表明：该太阳跟踪器能在不同天气状况下对太阳进行较准确地跟踪，能量接收效率提高了30%，达到充分利用太阳能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上传时间： 2013-10-15
上传用户：urgdil
