加密算法 Test Driver for Crypto++, a C++ Class Library of Cryptographic Primitives: - To generate an RSA key cryptest g - To encrypt and decrypt a string using RSA cryptest r - To calculate MD5, SHS, and RIPEMD-160 message digests: cryptest m file - To encrypt and decrypt a string using DES-EDE in CBC mode: cryptest t - To encrypt or decrypt a file cryptest e|d input output - To share a file into shadows: cryptest s <pieces> <pieces-needed> file (make sure file has no extension, if you re running this under DOS) - To reconstruct a file from shadows: cryptest j output file1 file2 [....] - To gzip a file: cryptest z <compression-level> input output - To gunzip a file: cryptest u input output - To run validation tests: cryptest v - To run benchmarks: cryptest b [time for each benchmark in seconds]
标签： Cryptographic Primitives generate Library
上传时间： 2015-07-16
上传用户：wqxstar
solve the 8-puzzle problem using A* algorithm. Definitely written by my self, also include BGI graphics library output.
标签： Definitely algorithm problem include
上传时间： 2014-01-17
上传用户：zm7516678
工程计算MATLAB code to calculate the reorthogonalized sine tapers input: N = the length of the time series data to be tapered p = the number of tapers requested I = the gap structure a vector of length N I(t) = 1 if there is data at time t, t=1, ..., N I(t) = 0 if there is a gap at time t output: X = N-by-p vector of the reorthogonalized sine taper
标签： the reorthogonalized calculate MATLAB
上传时间： 2013-12-17
上传用户：wangyi39
his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run "make" from the console in echomaster and echoslave subdirs. "make program" will program the device if you have a AVRISP attached. Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST! Otherwise you wont get any clock signal to the AVR and then you can t program it or reset the fuses! The MC1319x has default clock output of 32kHz so you will have to set your programmer to a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
标签： the 20060125 project WinAVR
上传时间： 2014-10-10
上传用户：yan2267246
C8051F020 ，通过串口发送HEX烧写文件，进行在程序编程
标签： C8051F020
上传时间： 2015-08-04
上传用户：ccclll
Test program to loop on Successive Approximation A-to-D conversion. Allows digital codes and resulting DAC output to be viewed on scope.
标签： Approximation Successive conversion program
上传时间： 2015-08-07
上传用户：顶得柱
8点基二fft Fast Fourier Transform (FFT). Using 8 points, takes about 1.2 ms to execute one FFT. Sets up General Purpose Timer 1 to generate events at 10 kHz. Will produce 10 kHz output on T1PWM and T1PWM pins.
标签： FFT Transform Fourier execute
上传时间： 2013-12-18
上传用户：Yukiseop
The book "The Finite Difference Time Domain for Electromagnetics" by Karl Kunz and Raymond Luebbers, CRC Press, 1993, contains an FDTD code and output files in Appendix B. The same code and output files are contained in this directory.
标签： Electromagnetics Difference The Luebbers
上传时间： 2013-12-29
上传用户：chongcongying
这是一个DELPHI与单片机相结合的应用例子 这个程序的主要功能是通过串口与单片机通讯，读写EEPROM的资料。 上位机程序是用Delphi 6.0，下位机程序是CVAVR 1.24， 采用的主芯片是Atmel ATMega16， EEPROM芯片是Atmel AT24C04(或AT24C256) Application ...... 应用程序 for Delphi 6.0 (SP2) ..\EEPROM.dpr ...... DELPHI 项目包 ..\EEPROM.res ...... DELPHI 项目包资源 ..\EEPROM.cfg ..\EEPROM.dof ..\EEPROM.exe ... 编译生成的可执行文件 ..\EEPROM_form.pas ... 主界面程序文件 ..\EEPROM_form.dfm ... 主界面资源文件 ..\HexTable.cds ... 内存表 Fireware ...... 固件程序 for CVAVR 1.24 (+) ..\TestEEPROM.prj ...... 项目程序 ..\TestEEPROM.c ...... 程序文件 ..\TestEEPROM.asm ...... 生成的汇编文件 ..\TestEEPROM.hex ...... 可烧录至Atmel ATMega16的文件
上传时间： 2013-12-10
上传用户：invtnewer
利用Atmel ATMega8 的定时器功能和PWM功能，制作频率发生器。 有LCD显示，并可实时调节ATMega8的各个相关的寄存器内容。 支持红外遥控器输入。 ..\频率发生器.prj ......主芯片项目文件 ..\频率发生器.c ......主芯片主程序 ..\频率发生器.asm ......主芯片汇编文件(自动生成) ..\频率发生器.hex ......可供烧录的文件 ..\频率发生器_client.prj ......副芯片项目文件 ..\频率发生器_client.c ......副芯片主程序 ..\频率发生器_client.asm ......副芯片汇编文件 ..\频率发生器_client.hex ......可供烧录的文件 ..\Config.h ......硬件配置文件 ..\Input.c ......接受红外遥控器输入并在LCD中显示 ..\LCD_Interface.c ......LCD 1602 接口文件 ..\Menu.c ......在LCD中显示菜单和其它信息 ..\Menu.h ......菜单定义文件 ..\Readme.txt ......本说明文件
上传时间： 2013-12-12
上传用户：源弋弋
