This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
标签： the Analyzer Compiler project
上传时间： 2013-12-19
上传用户：Yukiseop
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
This directory contains the memtest 8051 firmware for the Anchor Chips EZ-USB chip. The purpose of this software is to test the different memory segments in the Ez-Usb chip. This example will output the string "good" on the 7 segment LED if the mem test passes, or it will output the first address where the memtest fails.
标签： directory the contains firmware
上传时间： 2015-05-04
上传用户：zxc23456789
The LT® 1529/LT1529-3.3/LT1529-5 are 3A low dropout regulators with micropower quiescent current and shutdown. The devices are capable of supplying 3A of output current with a dropout voltage of 0.6V. Designed for use in battery-powered systems, the low quiescent current, 50mA operating and 16mA in shutdown, make them an ideal choice. The quiescent current is well controlled it does not rise in dropout as it does with many other low dropout PNP regulators.
标签： 1529 micropower regulators quiescent
上传时间： 2013-12-17
上传用户：qiao8960
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
标签： multiplication Implement matrices matrix
上传时间： 2014-08-30
上传用户：dsgkjgkjg
配合dsp_boot一起使用，可以将CCS2生成的.out文件转换成HEX文件格式，然后这可以实现DSP的boot_load
标签： dsp_boot
上传时间： 2015-05-16
上传用户：zhaoq123
简单混合衰落信道 This mfile inputs an unmodulated sinewave through a simple Rayleigh two path fading channel and shows the output with phase, gain, and attenuation characteristics via animation.
标签： unmodulated Rayleigh sinewave through
上传时间： 2015-05-17
上传用户：CSUSheep
单片机开发过程中用到的多功能工具，包括热敏电阻RT值--HEX数据转换；3种LED编码；色环电阻计算器；HEX/BIN 文件互相转换；eeprom数据到C/ASM源码转换；CRC校验生成；串口调试，带简单而实用的数据分析功能；串口/并口通讯监视等功能. 用C++ Builder开发，无须安装，直接运行，不对注册表进行操作。纯绿色软件。
上传时间： 2013-12-11
上传用户：希酱大魔王
数字运算，判断一个数是否接近素数 A Niven number is a number such that the sum of its digits divides itself. For example, 111 is a Niven number because the sum of its digits is 3, which divides 111. We can also specify a number in another base b, and a number in base b is a Niven number if the sum of its digits divides its value. Given b (2 <= b <= 10) and a number in base b, determine whether it is a Niven number or not. Input Each line of input contains the base b, followed by a string of digits representing a positive integer in that base. There are no leading zeroes. The input is terminated by a line consisting of 0 alone. Output For each case, print "yes" on a line if the given number is a Niven number, and "no" otherwise. Sample Input 10 111 2 110 10 123 6 1000 8 2314 0 Sample Output yes yes no yes no
上传时间： 2015-05-21
上传用户：daguda
单片机编成中常用的几种码制转换BCD，HEX，BIN
上传时间： 2015-05-23
上传用户：许小华
