基于TMS320F2812 光伏并网发电模拟装置PROTEL设计原理图+PCB+软件源码+WORD论文文档,硬件采用2层板设计，PROTEL99SE 设计的工程文件，包括完整的原理图和PCB文件，可以做为你的学习设计参考。 摘要：本文实现了一个基于TMS320F2812 DSP芯片的光伏并网发电模拟装置，采用直流稳压源和滑动变阻器来模拟光伏电池。通过TMS320F2812 DSP芯片ADC模块实时采样模拟电网电压的正弦参考信号、光伏电池输出电压、负载电压电流反馈信号等。经过数据处理后，用PWM模块产生实时的SPWM 波，控制MOSFET逆变全桥输出正弦波。本文用PI控制算法实现了输出信号对给定模拟电网电压的正弦参考信号的频率和相位跟踪，用恒定电压法实现了光伏电池最大功率点跟踪（MPPT），从而达到模拟并网的效果。另外本装置还实现了光伏电池输出欠压、负载过流保护功能以及光伏电池输出欠压、过流保护自恢复功能、声光报警功能、孤岛效应的检测、保护与自恢复功能。系统测试结果表明本设计完全满定设计要求。关键词：光伏并网，MPPT，DSP Photovoltaic Grid-connected generation simulator Zhangyuxin，Tantiancheng，Xiewuyang(College of Electrical Engineering, Chongqing University)Abstract: This paper presents a photovoltaic grid-connected generation simulator which is based on TMS320F2812 DSP, with a DC voltage source and a variable resistor to simulate the characteristic of photovoltaic cells. We use the internal AD converter to real-time sampling the referenced grid voltage signal, outputting voltage of photovoltaic, feedback outputting voltage and current signal. The PWM module generates SVPWM according to the calculation of the real-time sampling data, to control the full MOSFET inverter bridge output sine wave. We realized that the output voltage of the simulator can track the frequency and phase of the referenced grid voltage with PI regulation, and the maximum photovoltaic power tracking with constant voltage regulation, thereby achieved the purpose of grid-connected simulation. Additionally, this device has the over-voltage and over-current protection, audible and visual alarm, islanding detecting and protection, and it can recover automatically. The testing shows that our design is feasible.Keywords: Photovoltaic Grid-connected，MPPT，DSP 目录引言 11. 方案论证 11.1. 总体介绍 11.2. 光伏电池模拟装置 11.3. DC-AC逆变桥 11.4. MOSFET驱动电路方案 21.5. 逆变电路的变频控制方案 22. 理论分析与计算 22.1. SPWM产生 22.1.1. 规则采样法 22.1.2. SPWM 脉冲的计算公式 32.1.3. SPWM 脉冲计算公式中的参数计算 32.1.4. TMS320F2812 DSP控制器的事件管理单元 42.1.5. 软件设计方法 62.2. MPPT的控制方法与参数计算 72.3. 同频、同相的控制方法和参数计算 8
标签： tms320f2812 光伏 并网发电 模拟 protel pcb
上传时间： 2021-11-02
上传用户：
This document provides general hardware and layoutconsiderations and guidelines for hardware engineersimplementing a DDR3 memory subsystem.The rules and recommendations in this document serve as aninitial baseline for board designers to begin their specificimplementations, such as fly-by memory topology.
标签： ddr3
上传时间： 2021-11-21
上传用户：
It all started rather innocuously. I walked into Dr GT Murthy’s office one fine day, andchanged my life. “Doc” was then the General Manager, Central R&D, of a very largeelectrical company headquartered in Bombay. In his new state-of-the-art electronics center,he had hand-picked some of India’s best engineers (over a hundred already) ever assembledunder one roof. Luckily, he too was originally a Physicist, and that certainly helped me gainsome empathy. Nowadays he is in retirement, but I will always remember him as athoroughly fair, honest and facts-oriented person, who led by example. There were severalthings I absorbed from him that are very much part of my basic engineering persona today.You can certainly look upon this book as an extension of what Doc started many years agoin India … because that’s what it really is! I certainly wouldn’t be here today if I hadn’t metDoc. And in fact, several of the brash, high-flying managers I’ve met in recent years,desperately need some sort of crash course in technology and human values from Doc!
标签： 开关电源
上传时间： 2021-11-23
上传用户：
General Design Specification:1. AC Input Range 180-264Vac, Isolated ac-dc offline, 12LEDS,Output 700mA2. Intelligent wall dimmer detections(Leading-edge dimmer , Trailing-edgedimmer , No-dimmer)3. Multiple dimming control scheme4. Wide dimming range from 1% up to 100%5. No visible flicker6. Resonant control to achieve high efficiency7. High Power Factor, 0.9 without dimmer8. Temperature degrade control to adjust the LED9. Primary-only Sensing eliminates opto-isolator feedback and simplifies design
标签： iw3617
上传时间： 2021-12-03
上传用户：canderile
高通(Qualcomm)蓝牙芯片QCC5151_硬件设计详细指导书（官方内部培训手册）共52页其内容是针对硬件设计、部分重要元器件选择(ESD，Filter）及走线注意事项的详细说明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 2.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天线 走线的注意事项)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker output4.3 Line/Mic input 4.4 Headphone output optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 QSPIinterface 8 USB interfaces 8.1 USB device port8.1.1 USB connections8.1.2 Layout notes8.1.3 USB charger detection
上传时间： 2022-01-24
上传用户：XuVshu
一种通用微型飞行控制器设计 105页摘 要 微小型无人机(Micro／Mini UnmannedAerial Vehicle，M【，AV)在现代军事和国民经济中发 挥着越来越重要的作用。飞行控制器是无人机系统的核心，它自动采集无人机的各种飞行参数， 输出舵面／油门指令以控制无人机的姿态和轨迹，使无人机能在没有人工操纵干预的情况下自主 飞行，完成预定的任务。因此，研制高性能的飞行控制器对改善无人机的飞行性能以及提高任 务完成效率都具有重要的意义。 本文着重研究一种通用微型飞行控制器(General Micro Flight Controller，GMFC)，以适用 于小型／微型固定翼飞行器、旋翼飞行器、飞艇以及移动机器人的控制。论文的主要工作涉及 GMFC的硬件设计与软件实现，具体内容包括： 1)分析了微型飞行控制器在国内外的研究现状和发展趋势，根据任务需求和设计指标确定 一种通用型、微型化、低功耗、高性能、低成本的嵌入式微型飞行控制器的整体方案。 2)设计了基于ARM的通用微型飞行控制器的硬件系统，包括主控模块、惯性测量单元、 静压高度计、遥控信号接收单元、数据通信模块、电源模块、附加传感器模块等；完成了整个 控制器的PCB制作以及对所有电路的调试工作，使得系统运作正常。 3)研究了基于卡尔曼滤波算法的姿态参考系统，并对姿态参考系统的静态性能和动态性能 进行测试。 4)设计了小型四旋翼飞行器本体平台并对其进行动力学建模仿真； 5)在此基础上，结合四旋翼飞行器试验平台设计了飞行控制律，开发了GMFC的软件系 统，并开展物理实验验证。
标签： 飞行控制器
上传时间： 2022-03-15
上传用户：zhaiyawei
首先下载软件，解压软件，安装在程序中找到SEGGER,选里面的J-FLASH，进入界面，刚开始的那个界面可以忽略，不用建project也可以；单击菜单栏的“Options---Project settings”打开设置，进行jlink配置;正在General选项，选择“USB”，一般都是默认配置，确认一下即可;然后在CPU选项，选择芯片型号，先选择“Device”才能选择芯片型号，芯片型号，要根据你使用的芯片进行选择;在Target interface选项 里面选择SWD模式;首先Target里面选“Connection”连接目标芯片，然后 Target--Auto进行程序烧写;首先Target里面选择“Connection”连接目标芯片，然后 Target--Auto进行程序烧写.SEGGER J-Links are the most widely used line of debug probes available today. They've proven their value for more than 10 years in embedded development. This popularity stems from the unparalleled performance, extensive feature set, large number of supported CPUs, and compatibility with all popular development environments.
标签： JLINK
上传时间： 2022-03-22
上传用户：
高通(Qualcomm)蓝牙芯片QCC5144_硬件设计详细指导书（官方内部培训手册）其内容是针对硬件设计、部分重要元器件选择(ESD，Filter）及走线注意事项的详细说明。2 Power management 2.1 SMPS 2.1.1 Components specification 2.1.2 Input power supply selection 92.1.3 Minimize SMPS EMI emissions 2.1.4 Internal LDOs and digital core decoupling 2.1.5 Powering external components 2.2 Charger 2.2.1 Charger connections.2.2.2 General charger operation2.2.3 Temperature measurement during charging 2.3 SYS_CTRL 3 Bluetooth radio3.1 RF PSU component choice 3.2 RF band-pass filter3.3 Layout (天线 走线的注意事项)4 Audio4.1 Audio bypass capacitors 4.2 Earphone speaker output4.3 Line/Mic input 4.4 Headphone output optimizition5 LED pads 5.1 LED driver 5.2 Digital/Button input 5.3 Analog input5.4 Disabled 6 Reset pin (Reset#)7 USB interfaces7.1 USB device port7.1.1 USB device port7.1.2 Layout notes 7.1.3 USB charger detectionA QCC5144 VFBGA example schematic and BOM B Recommended SMPS components specificationB.1 Inductor specifition B.2 Recommended inductors B.3 SMPS capacitor specifition
上传时间： 2022-04-07
上传用户：默默
为了实时检测血氧量,能使缺氧特别敏感的脑组织或心脏类疾病患者得到及时治疗,采用近红外双波长透射式光电脉搏血氧测定法,以H桥电路对发射光源进行控制及通用运算放大器搭建滤波电路。运用参数理论计算和计算机仿真结果相对比的方法,通过Mu ltisim软件对所设计电路进行仿真,仿真结果与理论参数计算相吻合,证明了电路参数设计的可行性,为血氧仪的实物制作提供参考。For real-time detection of oxygen saturation for timely treatment of the brain or heart,which are very sensitive to oxygen inadequacy,the near-infrared wavelengths double photoelectric pulse oximeter transmission method is adopted.The illuminant is controlled with the H bridge circuit and the filter circuit is built with general op-amps.Parameters by theoretical calculation is compared with the computer simulation results in Multisim and satisfactory results are obtained.It is shown that the design of the circuit parameters is feasible and can be a help in making the physical blood-oxygen monitor.
上传时间： 2022-05-12
上传用户：
The information disclosed to you hereunder (the Materials ) is provided solely for the selection and use of Xilinx products. To the maximum extent permitted by applicable law: (1) Materials are made available"AS IS"and with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES AND CONDITIONS, EXPRESS, IMPLIED, OR ST ATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY NON-INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in contract or tort. includina nealigence. or under anv other theorv of liabilitv) for any loss or damage of any kind or nature related to, arising under, or in connection with, the Materials (including vour use of the Materials), including for any direct, indirect, special, incidental, or consequential loss or damage (including loss of data, profits, qoodwill, or any type of loss or damage suffered as a result of anv action brought by a third party)
上传时间： 2022-06-18
上传用户：
