The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签： Circuitry Operation Single Cell
上传时间： 2013-10-30
上传用户：hz07104032
In predominantly digital systems it is often necessaryto include linear circuit functions. Traditionally, separatepower supplies have been used to run the linear components(see Box, “Linear Power Supplies—Past, Present,and Future”).
标签： Designing Operation Circuits Linear
上传时间： 2013-11-04
上传用户：sdq_123
介绍了一款输入级采用差分放大作倒相的推挽功放, 它的额定输出功率为, 如果提高输出级电源电压, 还可在不变动电路条件下, 把输出功率提高到, 可以满足一些对功率要求比较高的发烧友需要。
上传时间： 2013-11-08
上传用户：zhaiye
基于CAE仿真技术，评估LED路灯在工作状态下的散热性能，并通过与实测数据的对比，证明CAE仿真技术的可靠性。在仿真数据的基础上，高效地评估LED路灯热设计优化方案的可行性。
上传时间： 2013-11-20
上传用户：wkchong
以单片开关电源的典型电路为例，详细阐述其波形测试方法并对实测波形作了深入分析，重点研究了单片开关电源的启动特性、一次侧和二次侧的电压波形及电流波形。所得出的结论对实现单片开关电源的优化设计具有重要参考价值。
上传时间： 2013-10-23
上传用户：笨小孩
K10的GPIO库函数之实现LED灯亮灭 T17D0 000:565 SEGGER J-Link V4.40c Log File (0001ms, 0563ms total)
上传时间： 2013-10-08
上传用户：ls530720646
目前Kinetis 系列MCU 家族中的Cortex-M0+仅支持SWD 调试接口，Cortex-M4 支持JTAG、cJTAG 和SWD 调试接口，同时还具有EzPort 编程接口。
上传时间： 2013-10-31
上传用户：zhouchang199
上一节，仔细的把怎么建立一个好的工程模板说了一下，可以说是一个好的
上传时间： 2013-11-25
上传用户：shawvi
采用模块化的编程方法，可以把相对复杂的软件系统分成功能相对独立的各个模块，这
上传时间： 2013-10-20
上传用户：suicoe
