实验教学一直是工科教学中不可或缺的组成部分,对培养学生的动手能力,独立思考能力,创新思维与发散思维具有重要的作用。针对目前电路教学实验中电路仿真实验与实物电路实验各自独立,无法统一问题,提出将仿真电路实验与实物电路实验有机的结合同步操作,并使用Web发布实现远程实验操作。采用Multisim作为电路实验仿真平台,NI Eiviss II作为实物电路实验硬件平台,运用LabVIEW整合Multisim电路仿真实验与实物电路实验,实现仿真与实物实验有机结合,两种实验可同步进行。学生在仿真实验中先可探索实验,然后做实物实验。同时运用LabVIEW开发出实验过程人机交互操作接口界面,使用过程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an important role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上传时间： 2022-04-05
上传用户：
高通蓝牙芯片QCC5144 详细规格手册datasheet （共99页）含各个接口说明，应用原理图等信息。 QualcommTrueWireless™ stereo earbuds (无线双耳） Features（特点） ■ Qualifiedto Bluetooth v5.2 specification （蓝牙协议标准5.2） ■ 120 MHz Qualcomm ® Kalimba ™ audio DSP （120MHz 的音频DSP处理器） ■ 32 MHz/80MHz Developer Processor for applications ■ Firmware Processor for system ■ Flexible QSPI flash programmable platform （可编程的QSPI外挂存储器） ■ High-performance 24‑bit audio interface （高性能的24位音频接口） ■ Digital and analog microphone interfaces （含 数字 及模拟 MIC接口） ■ Flexible PIO controller and LED pins with PWM support ■ Serial interfaces: UART, Bit Serializer (I²C/SPI), USB 2.0 （支持串口，I2C， SPI，USB 接口） ■ Advanced audio algorithms （高级的音频算法） ■ ActiveNoise Cancellation: （支持ANC 主动降噪功能） Hybrid, Feedforward, and Feedback modes, using Digital or Analog Mics, enabled using license keys available from Qualcomm® ■ Qualcomm ® aptX ™ and aptX HD Audio （支持独特的aptx 功能）
上传时间： 2022-04-07
上传用户：
高通蓝牙芯片QCC3040 详细规格手册datasheet （共96页）QualcommTrueWireless™ stereo earbuds (无线双耳）Features（特点）■ Qualifiedto Bluetooth v5.2 specification （蓝牙协议标准5.2）■ 120 MHz Qualcomm ® Kalimba ™ audio DSP （120MHz 的音频DSP处理器）■ 32 MHz Developer Processor for applications （32MH的 应用处理器）■ Firmware Processor for system■ Flexible QSPI flash programmable platform （可编程的QSPI外挂存储器）■ High-performance 24‑bit audio interface （高性能的24位音频接口）■ Digital and analog microphone interfaces （含 数字 及模拟 MIC接口）■ Flexible PIO controller and LED pins with PWM support■ Serial interfaces: UART, Bit Serializer (I²C/SPI), USB 2.0 （支持串口，I2C， SPI，USB 接口）■ Advanced audio algorithms （高级的音频算法）■ ActiveNoise Cancellation: （支持ANC 主动降噪功能）Hybrid, Feedforward, and Feedback modes, using Digitalor Analog Mics, enabled using license keys available from Qualcomm®■ Qualcomm ® aptX ™ and aptX HD Audio （支持独特的aptx 功能）
上传时间： 2022-04-09
上传用户：slq1234567890
基于TMS320F28335的超声波流量计硬件原理图+软件源码本文以TMS320F28335 处理器为核心，设计一种用于管道流量测量的超声波流量计。系统硬件由核心板，超声波发射和接收电路，切换电路，超声换能器，基于ADS805 的高速信号采集电路，人机交互以及电源等模块构成。采用时差法进行管道流量测量，时差测量采用SCOT 加权的广义互相关时延估计算法。本论文设计的超声波流量计具有测量速度快、准确性好、成本低等优点。关键字：C2000，超声波，流量，广义互相关算法AbstractA kind of ultrasonic flowmeter using for the pipe flow measurement is designed based onTMS320F28335 in this paper. The system hardware consists of the following parts: the core board,ultrasonic signal transmitter and receiver circuits, switch circuit, ultrasonic transducer, signalacquisition circuit based on ADS805, human-computer interaction module and power supplymodule, etc. The system use the method of time difference for pipeline flow measurement and thetime difference is calculated by the time-delay algorithm of SCOT weighted generalizedcross-correlation. The ultrasonic flowmeter has the features of high testing speed, high precisionand low cost, etc.Keywords: C2000,Ultrasonic, Flow, Generalized Cross-Correlation Algorithm
标签： tms320f28335 超声波流量计
上传时间： 2022-05-06
上传用户：
以STM32F103C8T6为核心,设计了无刷直流电机控制器硬件电路。电路主要包括IR2310构成的PWM驱动电路、IRF3808构成的逆变电路、增量式旋转编码构成的速度反馈电路。控制器具有CAN和RS232通信接口,可与计算机或PLC构成速度或位置伺服系统。利用由xPC目标搭建的半实物仿真平台对PI参数进行整定。测试了控制器的速度伺服响应性能,给定速度为2400rpm时,控制器响应时间为0.32s。实验结果表明,系统工作可靠,稳定性好,响应速度快,可以满足上肢康复机器人的机械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,inverter circuit formed by IRF3808,speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the speed is 2 400 rpm,the response time of the controller is 0...
上传时间： 2022-05-07
上传用户：
基于DSP28035的高速永磁无刷直流电机驱动系统，包括论文和软硬设计资料。摘要参赛作品为基于DSP28035的高速永磁无刷直流电机驱动系统。该系统以一台额定转速60 krpm的高速永磁无刷直流电机、交错并联的Buck电路以及全桥电路为硬件平台，以DSP28035为控制核心，实现了调压调速功能和基于坐标变换的无位置传感器新技术。为实现该系统要求，本作品充分利用了DSP28035的资源例如：CLA模块，模拟比较器、HPWM模块以及AD转换模块等。AbstractThis work is the drive system for a high speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s speed with voltage and the function of sensorless control based on the coordinate transformation. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁无刷直流电机驱动系统由于基波频率较高（一般在1kHZ以上），利用逆变桥斩波进行调速的控制方式通常会受到开关管开关频率的限制，因此该系统多采用三相全桥前级加Buck电路进承担调压调速的功能，而三相全桥主要承担逻辑换相的功能。然而，传统Buck电路所需电感的体积较大，增加了系统的体积，降低了系统的功率密度。
上传时间： 2022-05-08
上传用户：bluedrops
Chapter 1：Introduction and Overview Chapter 2：Switches，Buttons，and Knob 开关按钮Chapter 3：Clock Sources 时钟脉冲源Chapter 4：FPGA Configuration Options 配置Chapter 5：Character LCD Screen LCD显示屏特性Chapter 6：VGA Display Port VGA接口——接到显示器上Chapter 7：RS-232 Serial Ports RS-232接口——接器件Chapter 8：PS/2 Mouse/Keyboard Port PS/2鼠标键盘接口Chapter 9：Digital to Analog Converter（DAC）D/A接口Chapter 10：Analog Capture Circuit 模拟捕获电路Chapter 11：Intel StrataFlash Parallel NOR Flash PROM Chapter 12：SPI Serial Flash 串行外围接口系列闪存Chapter 13：DDR SDRAM 内存Chapter 14：10/100 Ethernet Physical Layer Interface以太网物理层接口Chapter 15：Expansion Connectors 扩展接口Chapter 16：XC2C64A CoolRunner-II CPLDChapter 17：DS2432 1-Wire SHA-1 EEPROMSpartan-3E入门实验板使设计人员能够即时利用Spartan-3E系列的完整平台性能。设备支持：Spartan-3E、CoolRunner-ll关键特性：Xilinx器件：Spartan-3E（50万门，XC3S500E-4FG320C），CoolRunnerTM-lI与Platform Flash时钟：50MHz晶体时钟振荡器存储器：128Mbit 并行Flash，16 Mbit SPI Flash，64MByte DDR SDRAM连接器与接口：以太网10/100Phy，JTAG USB下载，两个9管脚RS-232串行端口，PS/2类型鼠标/键盘端口，带按钮的旋转编码器，四个滑动开关，八个单独的LED输出
标签： Spartan-3E
上传时间： 2022-06-19
上传用户：kingwide
摘要：介绍了以FreeModbus协议找在嵌入式抢占实时操作系统μC/OS-l的STM32平台上，成功实现了Modbus协议的移植。通过详细分析FreeModbus协议花并编写STM32F103VET6微处理器的底层驱动，成功实现了工业Modbus协议RTU和ASCll两种模式的通信功能。测试结果表明，在实际工业生产控制和仪表开发中，应用Freemodbus协议，完全符合工业数据采集、实时控制和数据处理等厂级重复性和精确度要求，在一定程度上降低了工业仪表开发的周期及成本。关键词：实时操作系统，uC/OS-ll，FreeModbus，Modbus协议，STM32Abstract:This paper introduces FreeModbus stack transplanted to the STM32 platform which has been embedded in the preemptive real-time operating system uC/OS-ll，in order that the transplantation of the Modbus protocol is successfuly im-plemented.The FreeModbus stack is analyzed in detail and STM32F103VET6 microprocessor underlying driver is writed，so that the two Modbus industrial communication function RTU and ASCll are successfully realized.Keywords:time operating system，uC/OS-ll，.FreeModbus，Modbus协议，STM32
标签： freemodbus 通信协议
上传时间： 2022-06-25
上传用户：
一、建立基本的项目平台在建项目平台前需要做一些准备，选择一个盘建立 Platform”文件夹，在Platform"文件夹下建boot".HardWareTest"、"Project"、"Src"四个文件夹，boot"用来存放bootloader工程程序，HardWareTest"用来存放硬件自动测试工程程序，"Project"用来存放项目平台建立时生产的文件，"Src"用来存放STM32uCOSl工程的应用程序。下面开始建项目平台吧。步骤一：新建一个 IAR for ARM工程，File-> New-> Workspac创建一个新的工作空间，然后通过Project >Create New Project建立一个ARM的Empty project，点击“OK"后弹出工程保存菜单，填写工程名“STM32uCOSI"，然后点击“保存”，第一个工程建立完毕。步骤二：再建一个工程，通过Project > Create New Project建立一个ARM的Empty project，点击“OK"后弹出工程保存菜单，填写工程名“BOOT"，然后点击“保存”，第二个工程建立完毕。步骤三：建第三个工程，通过Project →> Create New Project建立一个ARM的Empty project，点击“OK"后弹出工程保存菜单，填写工程名“HardWareTest"，然后点击“保存"，第三个工程建立完毕。
上传时间： 2022-06-26
上传用户：
Simulation can provide a lot of information about what the system is doing. We canadd the effect of different element, like Encoder resolution, ADC sampling rate, etc and understand how does it affect the system. Another benefit is the possibility to slow down the process, to gain insight on what happens of fast systems or, vice versa, speed up slow process.Because National Instruments is a unique company in the fact the we provide a fullhardware solution couple with a full development platform, we can use this tools in very particular ways For example, it is possible to combine the LabVIEW Control Design and Simulation Module along with the FPGA module to quickly prototype a controller. One of the main benefits of this approach is that there is no need to compile the FPGA code, which allows for a quick algorithm design turnaround and debugging.
标签： pid控制
上传时间： 2022-07-20
上传用户：
