为提高发电机并联供电时负载分配均衡性，以运X飞机分布式环形配电网络为背景，运X飞机配电系统中的八台发电机采用分组并联的方式接入配电网，选取前舱配电系统上的两台发电机，研究当两台直流发电机分组并联时的负载分配均衡性条件，以及影响负载均衡分配的因素，更进一步提出负载均衡分配的解决方法。
上传时间： 2013-11-05
上传用户：zhanditian
为了提高电压表的测量精度和性价比，提出了一种以AT89C51单片机为控制核心的，基于Proteus仿真技术的数字电压表设计方案。详细介绍了数字电压表的硬件电路设计和软件编程方法，并利用Proteus 软件进行了仿真调试。结果表明，所设计的数字电压表结构简单，性价比高，并具有较高的测量精度；同时，也证明了Proteus仿真软件的运用，可以有效地缩短单片机系统的开发周期，降低开发成本。
上传时间： 2013-11-10
上传用户：xianglee
针对船舶电力系统脆性研究，从脆性致因的内部机制和外部机制入手，建立包含脆性环境和系统结构4 层分析模型。主要分析其下层模型结构，将脆性环境通过脆性事件分解为若干基本脆性根源，用德菲尔法-最大熵原理建立以脆性根源为基础的脆性风险模型，分析预测船舶电力系统的脆性过程。最后以某一个船舶电力系统为例，对在随机的某一年的脆性过程进行了分析，找到船舶电力系统崩溃的主脆性根源，与实际情况进行比较，说明了该方法的可行性。结果说明对于有效的防止船舶电力系统的崩溃，分析其脆性风险，应对其主要的脆性根源进行相应的控制。
上传时间： 2013-11-09
上传用户：ryb
为了提升电力飞机配电系统电压供应品质，本论文利用重构控制理论来设计电压调节器用以有效的达到电压调节的目的。利用Dobson和Chiang提出的电力系统模型并假设在配电系统中电容器与变压器为有效的控制输入，在本论文提出了电压调节器设计准则。更进一步我们以容错控制的观念来设计主动式及被动式容错控制律，使得飞机配电系统在控制器发生故障或异常情况时，依然可以达到电压调节的目的。
上传时间： 2013-11-02
上传用户：梧桐
针对10 kV农村电网电压质量问题，提出了一种新型的有载调压器--10 kV馈线自动调压器的设计方法，即详细说明了该调压器档位动作电压的整定原理及档位控制器的设计。该装置具有良好的控制和保护功能，并且可以通过无线通信实现外部控制。
上传时间： 2013-11-16
上传用户：Huge_Brother
精确度0.05%满刻度±1位数（Accuracy 0.05%F.S.±1digit） 可测量交直流电流/交直流电压/电位计/传送器/Pt-100/荷重元/电阻等信号（Measuring DCA/DCV/ACA/ACV/Potentiometer/Transmitter/Pt-100/Load Cell/Resistor/etc……） 显示范围0-19999可任意规划（Programmable rate 0 to 1999 digit） 小数点可任意规划（Decimal point can be modified） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2014-01-25
上传用户：RQB123
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
Abstract: It is critically important that lithium-ion battery stacks have a good battery-management system for monitoring many cellvoltages and cell temperatures. Without that monitoring, thermal runaway can lead to a battery explosion. This design idea presentsa low-power circuit that measures the temperature of up to 12 thermistors. It powers and configures the multiplexers, and also putsthe muxes into shutdown to save power when not measuring temperatures.
上传时间： 2013-10-29
上传用户：xwd2010
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
