说明： 51单片机控制fm1702射频读卡芯片读写mifare1卡全套资料。包括电路图，pcb板图，上、下位机软件及源码，stc单片机下载软件，各种资料文档等。(51 SCM control fm1702 RF reader CHIP card reader mifare1 a full set of data. Including the circuit diagram, pcb board map, the upper and lower-bit machine software and source code, stc SCM download software, all kinds of information documentation.)
上传时间： 2022-05-27
上传用户：
说明： 基于单片机的rc522模块的门禁系统源码以及原理图(The source code and schematic diagram of the entrance guard system of rc522 module based on single CHIP microcomputer)
标签： 门禁系统
上传时间： 2022-06-06
上传用户：ttalli
说明： 合泰单片机HT66F50例程工程源程序，合泰各种例程demo都在里面(HT66F50 routine engineering source program of Hetai single CHIP microcomputer)
标签： 单片机
上传时间： 2022-06-06
上传用户：默默
说明： 基于51单片机驱动ADS1115进行AD采集在1602上显示程序源码(Based on 51 single-CHIP drive diode for water lamp processing, including driving, testing, C file)
上传时间： 2022-06-07
上传用户：
RTL9047A 为车用乙太网single CHIP 交换机方案,如下图port0~port3 总共提供4ports 100BASE-T1,不用外挂PHY可节省cost 及PCB空间;port4为 selection port可选择设定100BASE-T1或SGMII,其SGMII个外接CPU或对接相同型号switch做cascade扩充;port5为 selection port可选择设定传统100base-TX FE PHY, SGMII或 RGMII/MII/RMII,其100base-TX 界面作为车载Diagnostic界面;port6为RGMII/MII/RMII 界面,可用来外接CPU或扩充网路界面等应用。
上传时间： 2022-06-07
上传用户：
ICN6201/02 is a bridge CHIP which receives MIPI® DSI inputs and sends LVDS outputs. MIPI® DSI supports up to 4 lanes and each lane operates at 1Gbps maximum; the totally maximum input bandwidth is 4Gbps; and the MIPI defined ULPS(ultra-low-power state) is also supported. ICN6201 decodes MIPI® DSI 18bepp RGB666 and 24bpp RGB888 packets.The LVDS output 18 or 24 bits pixel with 25MHz to 154MHz, by VESA or JEIDA format.ICN6201/02 support video resolution up to FHD (1920x1080) and WUXGA (1920x1200).ICN6201 adopts QFN48 package and ICN6202 adopts QFN40 package
标签： icn6202
上传时间： 2022-06-10
上传用户：kingwide
DescriptionThe IMX385LQR-C is a diagonal 8.35 mm (Type 1/2) CMOS active pixel type solid-state image sensor with a squarepixel array and 2.13 M effective pixels. This CHIP operates with analog 3.3 V, digital 1.2 V, and interface 1.8 V triplepower supply, and has low power consumption. High sensitivity, low dark current and no smear are achieved throughthe adoption of R, G and B primary color mosaic filters. This CHIP features an electronic shutter with variablecharge-integration time.(Applications: Surveillance cameras)
标签： CMOS传感器 IMX385LQR-C
上传时间： 2022-06-18
上传用户：
sony CMOS传感器datasheet，IMX178LQJ-C_Data_SheetDescriptionThe IMX178LQJ-C is a diagonal 8.92 mm (Type 1/1.8) CMOS active pixel type image sensor with a square pixelarray and 6.44 M effective pixels. This CHIP operates with analog 2.9 V, digital 1.2 V and interface 1.8 V triple powersupply, and has low power consumption.High sensitivity, low dark current and no smear are achieved through the adoption of R, G and B primary colormosaic filters.This CHIP features an electronic shutter with variable charge-integration time.(Applications: Surveillance cameras, FA cameras, Industrial cameras)
标签： CMOS传感器 IMX178LQJ-C
上传时间： 2022-06-18
上传用户：
INTRODUCTION In the past, adding speech recording and playback capability to a product meant using a digital signal processor or a specialized audio CHIP. Now, using a simplified Adaptive Differential Pulse Code Modulation(ADPCM) algorithm, these audio capabilities can be added to any PICmicro device. This application note will cover the ADPCM compression and decompression algorithms, performance comparison of all PICmicro devices, and an application using a PIC16C72 micro-controller.DEFINITION OF TERMS step size -value of the step used for quantization of ana-log signals and inverse quantization of a number of steps.quantization -the digital form of an analog input signal is represented by a finite number of steps.adaptive quantization -the step size of a quantizer is dramatically changed with time in order to adapt to a changing input signal.inverse quantizer -a finite number of steps is converted into a digital representation of an analog signal.
上传时间： 2022-06-20
上传用户：
1:打开J-Flash ARM后,首先点击File-OpenProject...,从中选择STM32F103RB.jflash。(例子芯片,直接在提示的目录下找) 2.点击File-Open data file...选择要烧录的可执行文件(.hex 或者 .bin) 3:options-project settings 在里面配置cpu型号,下载方式 4: 选择烧录文件后,点击Target-connect,链接一下硬件是否通。如果能够连接成功会了LOG窗口最后一行显示“Connected successfully”。5:按F3擦除芯片。6.按F5键将程序写入芯片。7.硬件链接上之后，点击Target-Secure CHIP防止程序被恶意读出。如果您的芯片用于调试，不要执行本步骤。
标签： J-Flash
上传时间： 2022-06-22
上传用户：kingwide
