锂电池BMS管理技术是移动机器人的关键技术,本文设计了基于bq76PL455、STM32F103的锂电池管理系统,实现了电池组电压、电流、过压、过流等状态监测;系统配置均衡电路,电池充电过程中若出现电池单体电压不平衡现象,会触发均衡电路,进而提高电池的安全性,延长使用寿命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the monitoring of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上传时间： 2022-04-02
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
应用无迹卡尔曼滤波算法（UKF）进行锂电池的SOC估计,采用Thevenin二阶RC等效电路模型,对HPPC电池脉冲充放电实验数据进行Matlab处理,得到较为准确的模型.通过在Matlab中编写算法程序,对不同工况的估计值与实际值进行误差估算及对比分析,通过此算法进行SOC估计,得到该算法可有效降低系统误差并纠正SOC的初值偏差.The non trace Calman filter （UKF） is applied to the SOC estimation of lithium battery. The Thevenin two order RC equivalent circuit model is used to process the HPPC battery pulse charge discharge experimental data by Matlab processing, and a more accurate model is obtained. By writing algorithm program in Matlab, the error estimation and comparison analysis of the estimated value and actual value of different states are carried out, and the SOC estimation is carried out by this algorithm. The algorithm can effectively reduce the system error and correct the initial value deviation of the SOC.
标签： 卡尔曼滤波
上传时间： 2022-05-03
上传用户：默默
The JW® 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of output current and offers low-power operation in miniaturized packaging. JW7805 supports fixed output voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low output noise and high PSRR are also friendly to RF systems.
标签： JW7805
上传时间： 2022-05-06
上传用户：slq1234567890
RX-8801 SA Features built-in 32.768 kHz DTCXO, High Stability Supports l'C-Bus's high speed mode (400 kHz)Alarm interrupt function for day, date, hour, and minute settings Fixed-cycle timer interrupt function Time update interrupt function32.768 kHz output with OE function Auto correction of leap years Wide interface voltage range: 2.2 V to 5.5 V Wide time-keeping voltage range:1.8 V to 5.5 V Low current consumption: 0.84A/3V (Typ.)is an IC bus interface-compliant real-time clock which includes a 32.768 kHz DTCXO In addition to providing a calendar (year, month, date, day, hour, minute, second) function and a clock counter function, this module provides an abundance of other functions including an alarm function, fixed-cycle timer unction, time update interrupt function, and 32.768 kHz output function.The devices in this module are fabricated via a C-MOS process for low current consumption, which enables ong-term battery back-up.
上传时间： 2022-06-17
上传用户：
·Overview:20 minutes-Introduction and Objectives-Motor Control Development Toolbox:Library blocks,FreeMASTER, and Bootloader·Hands-On Demo:50 minutes-Motor Kit(Describe Freescale 3-Phase Motor Kit)-Convert simple model to run on Motor Kit with MCD Toolbox and use FreeMASTER·Model Based Design:10 minutes-Model Based Design Steps:Simulation,SIL,PIL and ISO 26262-SIL/PIL Hands-On Demo Step 2& 3 of MBD·Motor Control:20 minutes-FOC Sensor-less control and how to use it to turn a motor·Motor Control Hands-On Demo:80 minutes-Implement FOC Sensor-less Motor Control on Motor Kit-Run software from the model and use FreeMASTER to monitor·Summary and Q&A:10 minutes
上传时间： 2022-06-24
上传用户：
BMS定义·BMS:Battery management system SYSTEM），其作用是对锂离子电池电压、电流、温度、容量、电池SOC荷电状态计量、电池与车体的绝缘状态等多种电池参数以CAN通讯的方式与车控电脑实时进行信息交换，确保电池的能量发挥到极致，使驾驶者能够随时掌握电池的工作状态，以保证电池的安全。BMS不仅是数字化智能电池系统的中枢神经，也是新能源汽车必不可少的关键部件·SOC:State of Charge，电池（组）荷电状态；·SOH:State of Health，电池健康度BMS功能·1）电池工作状态监控：主要指在电池的工作过程中，对电池的电压，温度，工作电流，电池电，绝缘阻抗，继电器状态等一系列电池相关参数进行实时监测或计算，并根据这些参数判断目前电池的状态，以进行相应的操作，防正电池的过充或过放。·2）电池充放电管理：在电池的充电或放电的过程中，根据环境状态，电池状态等相关参数对电池的充电或放电进行管理，设置电池的最佳充电或放电曲线（如充电电流，充电上限电压值，放电下限电压值等），实现电池过充，进蔽，垃流，是流，短路等保护3）单体电池间均衡：即为单体电池均衡充电，使电池组中各个电池都达到均衡一致的状态。均衡器是电池管理系统的核心部件。
上传时间： 2022-07-02
上传用户：slq1234567890
芯片cx21986 规格书，希望能有帮助
上传时间： 2022-07-17
上传用户：
3-phase Sensor-less Fan Motor DriverAM2355NThe AM2355N is a 3-phase sensor-less DC fan motor driver IC. It senses the BEMF (BackElectro-Motive Force) of the motor in rotation and provides corresponding commutation current tothe motor. Rotation speed can be controlled by PWM input signal. The drivers include LockDetection, Thermal Shutdown, and Over-current Protection. Forward and Reverse control.www.junmintech.com
标签： am2355n
上传时间： 2022-07-26
上传用户：
BMS即 Battery Management System，电池管理系统。作为新能源汽车“电核心技术之一，BMS在新能源车上扮演十分重要的作用。按照新能源汽车对电池管理的需求，BMS具备的功能包括电压/温度/电流采样及相应的过压、欠压、过温、过流保护，SOC/SOH估算、SOP预测、故障诊断、均衡控制、热管理和充电管理等。为了保证汽车电子电气的可靠性设计，在2011年发布了ISO26262道路车辆功能安全标准），ISO26262标准是源于工业功能安全标准（IEC61508）[1]。目前许多汽车企业和零部件企业在控制器开发过程中采用ISO26262这个标准，ISO26262包括了汽车电子电气开发中与安全相关的所有应用，制定了汽车整个生命周期中与安全相关的所有活动，ISO26262从需求开始，当中包括概念设计、软硬件设计，直至最后的生产、操作，都提出了相应的功能安全要求，其覆盖了汽车整个生命周期，从而保证安全相关的电子产品的功能性失效不会造成危险的发生。如下图所示
标签： bms
上传时间： 2022-08-09
上传用户：1208020161
