PIC单片机应用问答14篇
上传时间： 2013-10-20
上传用户：jiiszha
7.1 串行通信基本知识7.2 串行口及应用7.3 RS-232C标准接口总线 及串行通信硬件设计7.4 89C51与89C51点对点异步通信7.5 89C51与PC机间通信软件的设计7.6 PC机与多个单片机间的通信本章将介绍89C51串行口的结构及应用PC机与89C51间的双机通信一台PC机控制多台89C51前沿机的分布式系统，以及通信接口电路和软件设计，并给出设计实例，包括接口电路、程序框图、主程序和接收/发送子程序．
上传时间： 2013-10-27
上传用户：firstbyte
本文主要是针对家庭用户设计了一单相电能计量电路。此电路采用一款高精度单相电能计量芯片ADE7755来采集用户所使用的电量，并使用高性能的单片机AT89C51来作为整个电能采集电路的控制中心。文中给出了整个电能计量电路的组成框图、单相电能测量电路图以及软件流程图，最后介绍了试验情况并对试验结果进行了分析比较，通过实验表明该电能计量电路具有较高的测量精度。
上传时间： 2013-10-16
上传用户：一天睡三次
ADC 单片机的应用随着数字化时代的来临，使得现代家庭的生活愈来愈便利。以前的洗衣机，有好几个旋钮，使用者只能选择几项功能，转来转去，操作非常麻烦；自从加上了单片机之后，我们可以发现，洗衣机的功能变强了，但是操作变简单了，只要按几下按钮，就等着洗完衣服。除了洗衣机之外，家里的冰箱、电磁炉、电子锅、热水瓶等电器产品也都渐渐走向了数字化。数字化有以下优点：一是容易操作和控制，另一个是可以使用单片机来控制其功能，使其功能增强及使用方便。自然界的各种信号，如温度、湿度、压力、光、声音、气体都是模拟信号，要对自然界里的信号做处理，就需要一个传感器将自然界的各种信号，转换成电压或是电流信号，再将这些模拟信号，通过一个模拟-数字转换器(ADC)，转成数字信号，由单片机来对数字信号做处理。要是将ADC 内建于单片机中，则使用上更加便利，也可大幅度降低成本。将模拟信号数字化有利于处理、运算及显示，尤其是我们日常生活中的各种家电产品如：冷气机、除湿机、电冰箱、洗衣机、微波炉、电磁炉等，不胜枚举。
上传时间： 2013-10-20
上传用户：debuchangshi
介绍了用MCS51单片机与DM9008 Ethernet控制芯片进行接口，实现在Ethernet上收发数据包的具体方法。
上传时间： 2013-10-16
上传用户：wang5829
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
标签： Microcontr Stellaris Using the
上传时间： 2013-10-14
上传用户：blans
验证 UART 发送数据中断产生条件和接受数据中断产生条件
上传时间： 2013-10-28
上传用户：xauthu
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
Fuion时间上首个模数混合的FPGA，在PROASIC3的集成上加入FLSHMEMROY，ADC，RTC，以及RC振荡器等，使用SOC成为了可能。
上传时间： 2013-10-13
上传用户：2218870695
