本文是基于C8051F单片机的便携式农田基础信息采集系统的设计方案，为了克服现有农田综合数据采集设备的移动性差，高成本，使用复杂的不足，本文提供一种便携嵌入式农田基础数据采集终端，该终端具有体积小、功耗低、携带性好、操作简单、安装方便、模块化和可扩张性及网络化功能，农业生产管理人员可以随意携带到田间地头进行使用。
上传时间： 2013-11-09
上传用户：huyanju
基于单片机的多路数据采集系统
上传时间： 2014-12-26
上传用户：龙飞艇
单片机无线串行接口电路设计
上传时间： 2014-01-16
上传用户：aix008
PC与单片机数据采集系统的USB通讯设计论文
上传时间： 2013-10-30
上传用户：hanli8870
无线遥控模块（单片机）
上传时间： 2013-10-13
上传用户：netwolf
便携式信号采集在机器健康诊断系统中有较高的应用价值。机器健康诊断的信号特点是包括低频信号。本文研究是为了实现简易而且低成本的低频便携式信号采集。以Microchip公司单片机PIC18F1320为核心设计信号采集电路，实现了信号的采集和保存。系统采用串行电可擦除芯片24LC32A保存数据，经过有线通信，信号数据由串行口通过MAX232芯片输送到微型计算机接收和保存，最后绘制出信号波形。 微型计算机程序采用Visual Basic编程。研究成功采样频率为3 kHz的复杂信号，证明该方案符合设计要求。 Abstract: Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
上传时间： 2013-11-19
上传用户：moerwang
以C8051F020为核心处理器，设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络，结合嵌入式系统的软硬件技术，完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后，分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据，通过Zigbee无线网络传送到上位机，系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签： C8051F020 Zigbee 汽车测试 系统设计
上传时间： 2013-11-23
上传用户：dsgkjgkjg
介绍基于ISA总线与KH-9300的数据采集板卡的设置，详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等，探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法，应注意的主要问题及程序测试的结果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上传时间： 2013-11-14
上传用户：qq527891923
介绍一种基于C8051F060单片机和NAND Flash的数据采集存储系统，该系统可实现3路信号采样，每路采样率为5KS/s,通过异步串行通信接口实现数据传输。并详细说明系统的软件设计。 Abstract: An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
上传时间： 2013-10-12
上传用户：Jesse_嘉伟
介绍一种简单射频识别系统设计。该设计包括阅读器、应答器和线圈3部分。由单片机控制阅读器向应答器发射无线信号，并接收应答器回送的信号，再通过分析回送信号识别物品。阅读器和应答器之间以半双工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
上传时间： 2013-10-11
上传用户：plsee
