Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上传时间： 2014-01-18
上传用户：wenyuoo
Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上传时间： 2013-10-22
上传用户：ztj182002
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
A recent trend in the design of portable devices has beento use ceramic capacitors to filter DC/DC converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上传时间： 2013-11-05
上传用户：comer1123
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
文章阐述了零电压开关技术在移相全桥变换器中的应用, 提出了一种改进型的零电压零电流全桥移相开关电源, 对电路的工作原理、工作模式作了具体分析, 主要器件的参数选择作了设计, 并给出了由控制芯片UC3875 构成的3KW 实用高频开关电源。
上传时间： 2013-11-18
上传用户：zhanditian
摘要:双脉宽调制(PWM)控制的交—直—交电压型变频器适于用做交流励磁发电机的励磁电源,但交流励磁发电机运行状态的改变会引起双PWM交—直—交变频器直流链电压的波动,不利于整个发电系统的稳定运行。文中结合交流励磁发电机的运行特点,深入分析了直流链电压波动的原因,提出了基于转子侧变换器瞬时功率反馈控制的双PWM控制策略。实验结果验证了所提出的改进控制策略的正确性,该方法可有效维持发电机运行状态突变时直流链电压的稳定,大大增强了发电机系统的动态响应能力和稳定性。 关键词:交流励磁发电机;励磁电源;双PWM交—直—交变频器;直流链电压;瞬时功率反馈控制
上传时间： 2013-11-03
上传用户：wangjin2945
