ddr2_parameters.vh

sata_device_model,对做硬盘控制器的朋友有帮助

/****************************************************************************************
*
*   Disclaimer   This software code and all associated documentation, comments or other 
*  of Warranty:  information (collectively "Software") is provided "AS IS" without 
*                warranty of any kind. MICRON TECHNOLOGY, INC. ("MTI") EXPRESSLY 
*                DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED 
*                TO, NONINFRINGEMENT OF THIRD PARTY RIGHTS, AND ANY IMPLIED WARRANTIES 
*                OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. MTI DOES NOT 
*                WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE 
*                OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE. 
*                FURTHERMORE, MTI DOES NOT MAKE ANY REPRESENTATIONS REGARDING THE USE OR 
*                THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS, 
*                ACCURACY, RELIABILITY, OR OTHERWISE. THE ENTIRE RISK ARISING OUT OF USE 
*                OR PERFORMANCE OF THE SOFTWARE REMAINS WITH YOU. IN NO EVENT SHALL MTI, 
*                ITS AFFILIATED COMPANIES OR THEIR SUPPLIERS BE LIABLE FOR ANY DIRECT, 
*                INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES (INCLUDING, 
*                WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, 
*                OR LOSS OF INFORMATION) ARISING OUT OF YOUR USE OF OR INABILITY TO USE 
*                THE SOFTWARE, EVEN IF MTI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
*                DAMAGES. Because some jurisdictions prohibit the exclusion or 
*                limitation of liability for consequential or incidental damages, the 
*                above limitation may not apply to you.
*
*                Copyright 2003 Micron Technology, Inc. All rights reserved.
*
****************************************************************************************/

    // Timing parameters based on Speed Grade

`define sg3E;
//`define x16;

                                          // SYMBOL UNITS DESCRIPTION
                                          // ------ ----- -----------
`ifdef sg25E
    parameter TCK_MIN          =    2500; // tCK    ps    Minimum Clock Cycle Time
    parameter TJIT_PER         =     100; // tJIT(per)  ps Period JItter
    parameter TJIT_DUTY        =     100; // tJIT(duty) ps Half Period Jitter
    parameter TJIT_CC          =     200; // tJIT(cc)   ps Cycle to Cycle jitter
    parameter TERR_2PER        =     150; // tERR(nper) ps Accumulated Error (2-cycle)
    parameter TERR_3PER        =     175; // tERR(nper) ps Accumulated Error (3-cycle)
    parameter TERR_4PER        =     200; // tERR(nper) ps Accumulated Error (4-cycle)
    parameter TERR_5PER        =     200; // tERR(nper) ps Accumulated Error (5-cycle)
    parameter TERR_N1PER       =     300; // tERR(nper) ps Accumulated Error (6-10-cycle)
    parameter TERR_N2PER       =     450; // tERR(nper) ps Accumulated Error (11-50-cycle)
    parameter TQHS             =     300; // tQHS   ps    Data hold skew factor
    parameter TAC              =     400; // tAC    ps    DQ output access time from CK/CK#
    parameter TDS              =      50; // tDS    ps    DQ and DM input setup time relative to DQS
    parameter TDH              =     125; // tDH    ps    DQ and DM input hold time relative to DQS
    parameter TDQSCK           =     350; // tDQSCK ps    DQS output access time from CK/CK#
    parameter TDQSQ            =     200; // tDQSQ  ps    DQS-DQ skew, DQS to last DQ valid, per group, per access
    parameter TWPRE            =    0.35; // tWPRE  tCK   DQS Write Preamble
    parameter TIS              =     200; // tIS    ps    Input Setup Time
    parameter TIH              =     275; // tIH    ps    Input Hold Time
    parameter TRC              =   55000; // tRC    ps    Active to Active/Auto Refresh command time
    parameter TRCD             =   12000; // tRCD   ps    Active to Read/Write command time
    parameter TWTR             =    7500; // tWTR   ps    Write to Read command delay
    parameter TRP              =   12500; // tRP    ps    Precharge command period
    parameter TXARDS           =       8; // tXARDS tCK   Exit low power active power down to a read command
    parameter CL_MIN           =       5; // CL     tCK   Minimum CAS Latency
`else `ifdef sg25
    parameter TCK_MIN          =    2500; // tCK    ps    Minimum Clock Cycle Time
    parameter TJIT_PER         =     100; // tJIT(per)  ps Period JItter
    parameter TJIT_DUTY        =     100; // tJIT(duty) ps Half Period Jitter
    parameter TJIT_CC          =     200; // tJIT(cc)   ps Cycle to Cycle jitter
    parameter TERR_2PER        =     150; // tERR(nper) ps Accumulated Error (2-cycle)
    parameter TERR_3PER        =     175; // tERR(nper) ps Accumulated Error (3-cycle)
    parameter TERR_4PER        =     200; // tERR(nper) ps Accumulated Error (4-cycle)
    parameter TERR_5PER        =     200; // tERR(nper) ps Accumulated Error (5-cycle)
    parameter TERR_N1PER       =     300; // tERR(nper) ps Accumulated Error (6-10-cycle)
    parameter TERR_N2PER       =     450; // tERR(nper) ps Accumulated Error (11-50-cycle)
    parameter TQHS             =     300; // tQHS   ps    Data hold skew factor
    parameter TAC              =     400; // tAC    ps    DQ output access time from CK/CK#
    parameter TDS              =      50; // tDS    ps    DQ and DM input setup time relative to DQS
    parameter TDH              =     125; // tDH    ps    DQ and DM input hold time relative to DQS
    parameter TDQSCK           =     350; // tDQSCK ps    DQS output access time from CK/CK#
    parameter TDQSQ            =     200; // tDQSQ  ps    DQS-DQ skew, DQS to last DQ valid, per group, per access
    parameter TWPRE            =    0.35; // tWPRE  tCK   DQS Write Preamble
    parameter TIS              =     200; // tIS    ps    Input Setup Time
    parameter TIH              =     275; // tIH    ps    Input Hold Time
    parameter TRC              =   55000; // tRC    ps    Active to Active/Auto Refresh command time
    parameter TRCD             =   15000; // tRCD   ps    Active to Read/Write command time
    parameter TWTR             =   10000; // tWTR   ps    Write to Read command delay
    parameter TRP              =   15000; // tRP    ps    Precharge command period
    parameter TXARDS           =       8; // tXARDS tCK   Exit low power active power down to a read command
    parameter CL_MIN           =       6; // CL     tCK   Minimum CAS Latency
`else `ifdef sg3E
    parameter TCK_MIN          =    2500; // tCK    ps    Minimum Clock Cycle Time
    parameter TJIT_PER         =     125; // tJIT(per)  ps Period JItter
    parameter TJIT_DUTY        =     125; // tJIT(duty) ps Half Period Jitter
    parameter TJIT_CC          =     250; // tJIT(cc)   ps Cycle to Cycle jitter
    parameter TERR_2PER        =     175; // tERR(nper) ps Accumulated Error (2-cycle)
    parameter TERR_3PER        =     225; // tERR(nper) ps Accumulated Error (3-cycle)
    parameter TERR_4PER        =     250; // tERR(nper) ps Accumulated Error (4-cycle)
    parameter TERR_5PER        =     250; // tERR(nper) ps Accumulated Error (5-cycle)
    parameter TERR_N1PER       =     350; // tERR(nper) ps Accumulated Error (6-10-cycle)
    parameter TERR_N2PER       =     450; // tERR(nper) ps Accumulated Error (11-50-cycle)
    parameter TQHS             =     340; // tQHS   ps    Data hold skew factor
    parameter TAC              =     450; // tAC    ps    DQ output access time from CK/CK#
    parameter TDS              =     100; // tDS    ps    DQ and DM input setup time relative to DQS
    parameter TDH              =     175; // tDH    ps    DQ and DM input hold time relative to DQS
    parameter TDQSCK           =     400; // tDQSCK ps    DQS output access time from CK/CK#
    parameter TDQSQ            =     240; // tDQSQ  ps    DQS-DQ skew, DQS to last DQ valid, per group, per access
    parameter TWPRE            =    0.35; // tWPRE  tCK   DQS Write Preamble
    parameter TIS              =     200; // tIS    ps    Input Setup Time
    parameter TIH              =     275; // tIH    ps    Input Hold Time
    parameter TRC              =   54000; // tRC    ps    Active to Active/Auto Refresh command time
    parameter TRCD             =   12000; // tRCD   ps    Active to Read/Write command time
    parameter TWTR             =    7500; // tWTR   ps    Write to Read command delay
    parameter TRP              =   12000; // tRP    ps    Precharge command period
    parameter TXARDS           =       7; // tXARDS tCK   Exit low power active power down to a read command
    parameter CL_MIN           =       4; // CL     tCK   Minimum CAS Latency
`else `ifdef sg3
    parameter TCK_MIN          =    3000; // tCK    ps    Minimum Clock Cycle Time
    parameter TJIT_PER         =     125; // tJIT(per)  ps Period JItter
    parameter TJIT_DUTY        =     125; // tJIT(duty) ps Half Period Jitter
    parameter TJIT_CC          =     250; // tJIT(cc)   ps Cycle to Cycle jitter
    parameter TERR_2PER        =     175; // tERR(nper) ps Accumulated Error (2-cycle)
    parameter TERR_3PER        =     225; // tERR(nper) ps Accumulated Error (3-cycle)
    parameter TERR_4PER        =     250; // tERR(nper) ps Accumulated Error (4-cycle)
    parameter TERR_5PER        =     250; // tERR(nper) ps Accumulated Error (5-cycle)
    parameter TERR_N1PER       =     350; // tERR(nper) ps Accumulated Error (6-10-cycle)
    parameter TERR_N2PER       =     450; // tERR(nper) ps Accumulated Error (11-50-cycle)
    parameter TQHS             =     340; // tQHS   ps    Data hold skew factor
    parameter TAC              =     450; // tAC    ps    DQ output access time from CK/CK#
    parameter TDS              =     100; // tDS    ps    DQ and DM input setup time relative to DQS
    parameter TDH              =     175; // tDH    ps    DQ and DM input hold time relative to DQS
    parameter TDQSCK           =     400; // tDQSCK ps    DQS output access time from CK/CK#
    parameter TDQSQ            =     240; // tDQSQ  ps    DQS-DQ skew, DQS to last DQ valid, per group, per access
    parameter TWPRE            =    0.35; // tWPRE  tCK   DQS Write Preamble
    parameter TIS              =     200; // tIS    ps    Input Setup Time
    parameter TIH              =     275; // tIH    ps    Input Hold Time
    parameter TRC              =   55000; // tRC    ps    Active to Active/Auto Refresh command time
    parameter TRCD             =   15000; // tRCD   ps    Active to Read/Write command time
    parameter TWTR             =    7500; // tWTR   ps    Write to Read command delay
    parameter TRP              =   15000; // tRP    ps    Precharge command period
    parameter TXARDS           =       7; // tXARDS tCK   Exit low power active power down to a read command
    parameter CL_MIN           =       6; // CL     tCK   Minimum CAS Latency
`else `ifdef sg37E
    parameter TCK_MIN          =    3750; // tCK    ps    Minimum Clock Cycle Time
    parameter TJIT_PER         =     125; // tJIT(per)  ps Period JItter
    parameter TJIT_DUTY        =     125; // tJIT(duty) ps Half Period Jitter
    parameter TJIT_CC          =     250; // tJIT(cc)   ps Cycle to Cycle jitter
    parameter TERR_2PER        =     175; // tERR(nper) ps Accumulated Error (2-cycle)
    parameter TERR_3PER        =     225; // tERR(nper) ps Accumulated Error (3-cycle)
    parameter TERR_4PER        =     250; // tERR(nper) ps Accumulated Error (4-cycle)
    parameter TERR_5PER        =     250; // tERR(nper) ps Accumulated Error (5-cycle)
    parameter TERR_N1PER       =     350; // tERR(nper) ps Accumulated Error (6-10-cycle)
    parameter TERR_N2PER       =     450; // tERR(nper) ps Accumulated Error (11-50-cycle)
    parameter TQHS             =     400; // tQHS   ps    Data hold skew factor
    parameter TAC              =     500; // tAC    ps    DQ output access time from CK/CK#