The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
标签： pw2601
上传时间： 2022-02-11
上传用户：
The PW2228A is a high efficiency single inductor Buck-Boost converter which can supply theload current up to 1.5A. It provides auto-transition between Buck and Boost Mode. The PW2228Aoperates at 2.4MHz switching frequency in CCM. DC/DC converter operates at Pulse-Skipping Modeat light load. The output voltage is programmable using an external resistor divider, or is fixed to3.3V internally. The load is disconnected from the VIN during shutdown.The PW2228A is available in TDFN3X3-10 package.
标签： pw2228a
上传时间： 2022-02-11
上传用户：
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
M.NT68676.2A is a monitor control board, which is suitable for Asia-Pacific market. It can supportLED/LCD panels which resolution is up to 2048×1152.M.NT68676.2A can synchronize with computer automatically. Synchronization requires thesynchronous signal which horizontal and vertical sync are separated.M.NT68676.2A can support dynamic contrast control, headphone input and Digital volume controlsimultaneously.
标签： 乐华驱动板
上传时间： 2022-03-13
上传用户：kent
意法半导体STM8系列参考手册Program memory: 8 Kbyte Flash memory; dataretention 20 years at 55 °C after 100 cycles• RAM: 1 Kbyte• Data memory: 128 bytes true data EEPROM;endurance up to 100 k write/erase cycles
标签： stm8
上传时间： 2022-04-27
上传用户：zhaiyawei
The JW® 7805 is a low noise low-dropout (LDO) voltage regulator with enable function that operates from 1.8V to 5.5V. It provides up to 300mA of output current and offers low-power operation in miniaturized packaging. JW7805 supports fixed output voltage 0.9V, 1.0V, 1.05V, 1.1V,1.2V, 1.3V, 1.35V, 1.5V, 1.8V, 1.85V, 2.1V, 2.2V, 2.3V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 2.9V, 3.0V,3.1V, 3.3V, 3.6V, 4.2V, 4.4V and 5.0V. The features of low quiescent current as low as 6uA and almost zero disable current are ideal for powering the battery equipment. JW7805’s low output noise and high PSRR are also friendly to RF systems.
标签： JW7805
上传时间： 2022-05-06
上传用户：slq1234567890
ICN6201/02 is a bridge chip which receives MIPI® DSI inputs and sends LVDS outputs. MIPI® DSI supports up to 4 lanes and each lane operates at 1Gbps maximum; the totally maximum input bandwidth is 4Gbps; and the MIPI defined ULPS(ultra-low-power state) is also supported. ICN6201 decodes MIPI® DSI 18bepp RGB666 and 24bpp RGB888 packets.The LVDS output 18 or 24 bits pixel with 25MHz to 154MHz, by VESA or JEIDA format.ICN6201/02 support video resolution up to FHD (1920x1080) and WUXGA (1920x1200).ICN6201 adopts QFN48 package and ICN6202 adopts QFN40 package
标签： icn6202
上传时间： 2022-06-10
上传用户：kingwide
Introduction The Sil9135/Sil9135A HDMI Receiver with Enhanced Audio and Deep Color Outputs is a second-generation dual-input High Definition Multimedia Interface(HDMI)receiver. It is software-compatible with the Sil9133receiver, but adds audio support for DTS-HD and Dolby TrueHD. Digital televisions that can display 10-or 12-bit color depth can now provide the highest quality protected digital audio and video over a single cable. The Sil9135and Sil9135A devices, which are functionally identical, can receive Deep Color video up to 12-bit,1080p @60Hz. Backward compatibility with the DVI 1.0specification allows HDMI systems to connect to existing DVI 1.0 hosts, such as HD set-top boxes and PCs. Silicon Image HDMI receivers use the latest generation Transition Minimized Differential Signaling(TMDS) core technology that runs at 25-225 MHz.The chip comes pre-programmed with High-bandwidth?
上传时间： 2022-06-25
上传用户：
AR0231AT7C00XUEA0-DRBR（RGB滤光）安森美半导体推出采用突破性减少LED闪烁 (LFM)技术的新的230万像素CMOS图像传感器样品AR0231AT，为汽车先进驾驶辅助系统(ADAS)应用确立了一个新基准。新器件能捕获1080p高动态范围(HDR)视频，还具备支持汽车安全完整性等级B(ASIL B)的特性。LFM技术(专利申请中)消除交通信号灯和汽车LED照明的高频LED闪烁，令交通信号阅读算法能于所有光照条件下工作。AR0231AT具有1/2.7英寸(6.82 mm)光学格式和1928(水平) x 1208(垂直)有源像素阵列。它采用最新的3.0微米背照式(BSI)像素及安森美半导体的DR-Pix™技术，提供双转换增益以在所有光照条件下提升性能。它以线性、HDR或LFM模式捕获图像，并提供模式间的帧到帧情境切换。 AR0231AT提供达4重曝光的HDR，以出色的噪声性能捕获超过120dB的动态范围。AR0231AT能同步支持多个摄相机，以易于在汽车应用中实现多个传感器节点，和通过一个简单的双线串行接口实现用户可编程性。它还有多个数据接口，包括MIPI(移动产业处理器接口)、并行和HiSPi(高速串行像素接口)。其它关键特性还包括可选自动化或用户控制的黑电平控制，支持扩频时钟输入和提供多色滤波阵列选择。封装和现状：AR0231AT采用11 mm x 10 mm iBGA-121封装，现提供工程样品。工作温度范围为-40℃至105℃(环境温度)，将完全通过AEC-Q100认证。
标签： 图像传感器
上传时间： 2022-06-27
上传用户：XuVshu
Datasheet SHT3x-DISHumidity and Temperature Sensor Fully calibrated, linearized, and temperaturecompensated digital output Wide supply voltage range, from 2.4 V to 5.5 V I2C Interface with communication speeds up to 1MHz and two user selectable addresses Typical accuracy of 2 %RH and 0.3 °C Very fast start-up and measurement time Tiny 8-Pin DFN package
上传时间： 2022-06-29
上传用户：
