SPI（Serial Peripheral Interface，串行外围接口）是Motorola公司提出的外围接口协议，它采用一个串行、同步、全双工的通信方式，解决了微处理器和外设之间的串行通信问题，并且可以和多个外设直接通信，具有配置灵活，结构简单等优点。根据全功能SPI总线的特点，设计的SPI接口可以最大发送和接收16位数据；在主模式和从模式下SPI模块的时钟频率最大可以达到系统时钟的1/4，并且在主模式下可以提供具有四种不同相位和极性的时钟供从模块选择；可以同时进行发送和接收操作，拥有中断标志位和溢出中断标志位。
上传时间： 2013-11-11
上传用户：himbly
Abstract: How can an interface change a happy face to a sad face? Engineers have happy faces when an interface works properly.Sad faces indicate failure somewhere. Because interfaces between microprocessors and ICs are simple—even easy—they are oftenignored until interface failure causes sad faces all around. In this article, we discuss a common SPI error that can be almostimpossible to find in a large system. Links to interface tutorial information are provided for complete information. Noise as a systemissue and ICs to minimize its effects are also described.
上传时间： 2013-11-18
上传用户：zgz317
SL811开发资料_包含源程序_电路图_芯片资料:SL811HS Embedded USB Host/Slave Controller.The SL811HS is an Embedded USB Host/Slave Controller capable of communicate with either full-speed or low-speed USB peripherals. The SL811HS can interface to devices such as microprocessors, microcontrollers, DSPs, or directly to a variety of buses such as ISA, PCMCIA, and others. The SL811HS USB Host Controller conforms to USB Specification 1.1.The SL811HS USB Host/Slave Controller incorporates USB Serial Interface functionality along with internal full-/low-speed transceivers.The SL811HS supports and operates in USB full-speed mode at 12 Mbps, or at low-speed 1.5-Mbps mode.The SL811HS data port and microprocessor interface provide an 8-bit data path I/O or DMA bidirectional, with interrupt support to allow easy interface to standard microprocessors or microcontrollers such as Motorola or Intel CPUs and many others. Internally,the SL811HS contains a 256-byte RAM data buffer which is used for control registers and data buffer.The available package types offered are a 28-pin PLCC (SL811HS) and a 48-pin TQFP package (SL811HST-AC). Both packages operate at 3.3 VDC. The I/O interface logic is 5V-tolerant.
上传时间： 2013-12-22
上传用户：a82531317
超声波传感器适用于对大幅的平面进行静止测距。普通的超声波传感器测距范围大概是 2cm~450cm，分辨率3mm（淘宝卖家说的，笔者测试环境没那么好，个人实测比较稳定的 距离10cm~2m 左右，超过此距离就经常有偶然不准确的情况发生了，当然不排除笔者技术 问题。） 测试对象是淘宝上面最便宜的SRF-04 超声波传感器，有四个脚：5v 电源脚（Vcc），触发控制端（Trig），接收端（Echo），地端（GND） 附:SRF 系列超声波传感器参数比较 模块工作原理： 采用IO 触发测距，给至少10us 的高电平信号； 模块自动发送8个40KHz 的方波，自动检测是否有信号返回； 有信号返回，通过IO 输出一高电平，高电平持续的时间就是超声波从发射到返回的时间．测试距离=(高电平时间*声速(340m/s))/2; 电路连接方法 Arduino 程序例子： constintTrigPin = 2; constintEchoPin = 3; floatcm; voidsetup() { Serial.begin(9600); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT); } voidloop() { digitalWrite(TrigPin, LOW); //低高低电平发一个短时间脉冲去TrigPin delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite(TrigPin, LOW); cm = pulseIn(EchoPin, HIGH) / 58.0; //将回波时间换算成cm cm = (int(cm * 100.0)) / 100.0; //保留两位小数 Serial.print(cm); Serial.print("cm"); Serial.println(); delay(1000); }
上传时间： 2013-11-01
上传用户：xiaoyuer
用途：测量地磁方向，测量物体静止时候的方向，测量传感器周围磁力线的方向。注意，测量地磁时候容易受到周围磁场影响，主芯片HMC5883 三轴磁阻传感器特点（抄自网上）： 1，数字量输出：I2C 数字量输出接口，设计使用非常方便。 2，尺寸小: 3x3x0.9mm LCC 封装，适合大规模量产使用。 3，精度高：1－2 度，内置12 位A/D,OFFSET, SET/RESET 电路，不会出现磁饱和现象，不会有累加误差。 4，支持自动校准程序，简化使用步骤，终端产品使用非常方便。 5，内置自测试电路，方便量产测试，无需增加额外昂贵的测试设备。 6，功耗低：供电电压1.8V, 功耗睡眠模式-2.5uA 测量模式-0.6mA 连接方法： 只要连接VCC，GND，SDA，SDL 四条线。 Arduino GND -> HMC5883L GND Arduino 3.3V -> HMC5883L VCC Arduino A4 (SDA) -> HMC5883L SDA Arduino A5 (SCL) -> HMC5883L SCL (注意，接线是A4，A5，不是D4,D5) 源程序： #include <Wire.h> #include <HMC5883L.h> HMC5883Lcompass; voidsetup() { Serial.begin(9600); Wire.begin(); compass = HMC5883L(); compass.SetScale(1.3); compass.SetMeasurementMode(Measurement_Continuous); } voidloop() { MagnetometerRaw raw = compass.ReadRawAxis(); MagnetometerScaled scaled = compass.ReadScaledAxis(); float xHeading = atan2(scaled.YAxis, scaled.XAxis); float yHeading = atan2(scaled.ZAxis, scaled.XAxis); float zHeading = atan2(scaled.ZAxis, scaled.YAxis); if(xHeading < 0) xHeading += 2*PI; if(xHeading > 2*PI) xHeading -= 2*PI; if(yHeading < 0) yHeading += 2*PI; if(yHeading > 2*PI) yHeading -= 2*PI; if(zHeading < 0) zHeading += 2*PI; if(zHeading > 2*PI) zHeading -= 2*PI; float xDegrees = xHeading * 180/M_PI; float yDegrees = yHeading * 180/M_PI; float zDegrees = zHeading * 180/M_PI; Serial.print(xDegrees); Serial.print(","); Serial.print(yDegrees); Serial.print(","); Serial.print(zDegrees); Serial.println(";"); delay(100); }
上传时间： 2014-03-20
上传用户：tianyi223
S3C44BOX的BIOS。可使用的命令：help --- show help ? --- = help date --- show or set current date time --- show or set current time setweek --- set weekday clock --- show system running clock setmclk --- set system running clock setbaud ------ set baud rate ipcfg ------ show or set IP address load ------ load file to ram comload ------ load file from serial port run ------ run from sdram prog ------ program flash copy ------ copy flash from src to dst address boot ------ boot from flash backup ------ move bios to the top of flash md ------ show memory data move ------ move program from flash to sdram
上传时间： 2015-01-22
上传用户：ANRAN
Altera recommends the following system configuration: * Pentium II 400 with 512-MB system memory (faster systems give better software performance) * SVGA monitor * CD-ROM drive * One or more of the following I/O ports: - USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications cables, or APU programming unit - Parallel port for ByteBlasterMV(TM) or ByteBlaster(TM) II download cables - Serial port for MasterBlaster communications cable * TCP/IP networking protocol installed * Windows 2000, Windows NT 4.0 with Service Pack 3 or later, or Windows XP * Internet Explorer 5.0 or later Memory & Disk Space Requirements USB开发
标签： system configuration recommends following
上传时间： 2015-03-27
上传用户：13188549192
CBC下写的串口编程，API函数实例 I wish this site had been around when I was trying to figure out how to make serial communications work in Windows95. I, like many programmers, was hit with the double-whammy of having to learn Windows programming and Win95 serial comm programming at the same time. I found both tasks confusing at best. It was particularly frustrating because I had, over the years, written so much stuff (including lots of serial comm software) for the DOS environment and numerous embedded applications. Interrupt driven serial comm, DMA transfer serial comm, TSR serial comm, C, assembler, various processors... you name it, it had written it. Yet, everything I knew seemed upside-down in the message-driven-callback world of Windows.
上传时间： 2014-06-20
上传用户：cccole0605
Bus Hound 5.0 Released by RAINMAN Installation: Simply install and when asked use whatever serial you want
标签： Installation Released whatever RAINMAN
上传时间： 2015-04-21
上传用户：
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
