1. 目的 规范产品的PCB焊盘设计工艺， 规定PCB焊盘设计工艺的相关参数，使得PCB 的设计满足可生产性、可测试性、安规、EMC、EMI 等的技术规范要求,在产品设计过程中构建产品的工艺、技术、质量、成本优势。 2. 适用范围本规范适用于空调类电子产品的PCB 工艺设计，运用于但不限于PCB 的设计、PCB 批产工艺审查、单板工艺审查等活动。本规范之前的相关标准、规范的内容如与本规范的规定相抵触的，以本规范为准3.引用/参考标准或资料TS-S0902010001 <〈信息技术设备PCB 安规设计规范〉>TS—SOE0199001 <〈电子设备的强迫风冷热设计规范〉〉TS—SOE0199002 〈<电子设备的自然冷却热设计规范>>IEC60194 〈<印制板设计、制造与组装术语与定义>> （Printed Circuit Board designmanufacture and assembly-terms and definitions)IPC—A-600F 〈<印制板的验收条件>〉 （Acceptably of printed board)IEC609504。规范内容4。1焊盘的定义 通孔焊盘的外层形状通常为圆形、方形或椭圆形。具体尺寸定义详述如下，名词定义如图所示。1) 孔径尺寸:若实物管脚为圆形：孔径尺寸(直径)=实际管脚直径+0。20∽0。30mm（8。0∽12。0MIL）左右；若实物管脚为方形或矩形：孔径尺寸（直径）=实际管脚对角线的尺寸+0.10∽0。20mm（4.0∽8。0MIL）左右。2) 焊盘尺寸： 常规焊盘尺寸=孔径尺寸（直径)+0.50mm（20.0 MIL)左右.…………
标签： PCB
上传时间： 2022-05-24
上传用户：canderile
AR0231AT7C00XUEA0-DRBR（RGB滤光）安森美半导体推出采用突破性减少LED闪烁 (LFM)技术的新的230万像素CMOS图像传感器样品AR0231AT，为汽车先进驾驶辅助系统(ADAS)应用确立了一个新基准。新器件能捕获1080p高动态范围(HDR)视频，还具备支持汽车安全完整性等级B(ASIL B)的特性。LFM技术(专利申请中)消除交通信号灯和汽车LED照明的高频LED闪烁，令交通信号阅读算法能于所有光照条件下工作。AR0231AT具有1/2.7英寸(6.82 mm)光学格式和1928(水平) x 1208(垂直)有源像素阵列。它采用最新的3.0微米背照式(BSI)像素及安森美半导体的DR-Pix™技术，提供双转换增益以在所有光照条件下提升性能。它以线性、HDR或LFM模式捕获图像，并提供模式间的帧到帧情境切换。 AR0231AT提供达4重曝光的HDR，以出色的噪声性能捕获超过120dB的动态范围。AR0231AT能同步支持多个摄相机，以易于在汽车应用中实现多个传感器节点，和通过一个简单的双线串行接口实现用户可编程性。它还有多个数据接口，包括MIPI(移动产业处理器接口)、并行和HiSPi(高速串行像素接口)。其它关键特性还包括可选自动化或用户控制的黑电平控制，支持扩频时钟输入和提供多色滤波阵列选择。封装和现状：AR0231AT采用11 mm x 10 mm iBGA-121封装，现提供工程样品。工作温度范围为-40℃至105℃(环境温度)，将完全通过AEC-Q100认证。
标签： 图像传感器
上传时间： 2022-06-27
上传用户：XuVshu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
8051 VARIOUS UTILITY FUNCTIONSUTIL_ADCAD - Add Acc to DPTR, sets CYUTIL_ADCBAD - Add B/A to DPTR, sets CYUTIL_SUBBAD
标签： FUNCTIONSUTIL_ADCAD DPTR CYUTIL_ADCBAD Add
上传时间： 2013-11-25
上传用户：himbly
b to b 模式 电子商务系统 ，c# 开发 , B/S结构
上传时间： 2014-01-20
上传用户：hanli8870
This project attempts to implement a Database using B+Tree. The project has developed a DATABASE SYSTEM with lesser memory consumption. Its API includes simple SQL Statements and the output is displayed on the screen. Certain applications for which several features of existing databases like concurrency control, transaction management, security features are not enabled. B+Trees can be used as an index for factor access to the data. Help facility is provided to know the syntax of SQL Statements.
标签： project implement developed Database
上传时间： 2013-12-25
上传用户：semi1981
Bing is a point-to-point bandwidth measurement tool (hence the b ), based on ping. Bing determines the real (raw, as opposed to available or average) throughput on a link by measuring ICMP echo requests roundtrip times for different packet sizes for each end of the link
标签： Bing point-to-point measurement determines
上传时间： 2015-09-15
上传用户：lgnf
If we have two individually sorted vectors "a" and "b" but they are not sorted with respect to each other and we want to merge them into vector "c" such that "c" is also a sorted vector. Then c=mergesorted(a,b) can be used.
标签： sorted individually respect vectors
上传时间： 2015-09-23
上传用户：comua
convert numbers from h to d or b to h
上传时间： 2014-11-17
上传用户：refent
杭电 ACM 1002 I have a very simple problem for you. Given two integers A and B, your job is to calculate the Sum of A + B.
标签： integers problem calcul simple
上传时间： 2014-01-12
上传用户：dave520l
