The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
为解决传统可视倒车雷达视频字符叠加器结构复杂，可靠性差，成本高昂等问题，在可视倒车雷达设计中采用视频字符发生器芯片MAX7456。该芯片集成了所有用于产生用户定义OSD，并将其插入视频信号中所需的全部功能，仅需少量的外围阻容元件即可正常工作。给出了以MAX7456为核心的可视倒车雷达的软、硬件实现方案及设计实例。该方案具有电路结构简单、价格低廉、符合人体视觉习惯的特点。经实际装车测试，按该方案设计的可视倒车雷达视场清晰、提示字符醒目、工作可靠，可有效降低驾驶员倒车时的工作强度、减少倒车事故的发生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
上传时间： 2013-12-10
上传用户：qiaoyue
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上传时间： 2013-11-08
上传用户：laozhanshi111
What is New in C51 Version 8.18[Device Support]Added debug support for the NXP P89LPC9408 in the LPC900 EPM Emulator/Programmer.[New Supported Device]Nuvoton W681308 device.[New Supported Device]NXP P89LPC9201, P89LPC9211, P89LPC922A1, P89LPC9241, P89LPC9251, P89LPC9301, P89LPC931A1, P89LPC9331, P89LPC9341, and P89LPC9351 devices.[New Supported Device]SiLabs C8051F500, C8051F501, C8051F504, C8051F505, C8051F506, C8051F507, C8051F508, C8051F509, C8051F510, and C8051F511 devices.[ULINK2 Support]Corrected potential deadlock on ST uPSD targets.[Device Simulation]Corrected simulation of Infineon XC800 MDU.[Device Simulation]Corrected behaviour of EXFn and TOGn on SiLabs C8051F12x/F13x devices.[Device Simulation]Added simulation for Atmel AT89C51RE2, including simulation of second UART.[Cx51 Compiler]Corrected failed initialization on far addresses when the object is located with _at_. 本资料仅供学习评估之用,请勿用于商业用途!请在学习评估24小时内删除.
上传时间： 2013-11-01
上传用户：panpanpan
The LPC1769/68/67/66/65/64 are ARM Cortex-M3 based microcontrollers for embedded applications featuring a high level of integration and low power consumption. The ARM Cortex-M3 is a next generation core that offers system enhancements such as enhanced debug features and a higher level of support block integration.
上传时间： 2014-02-20
上传用户：13215175592
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
The Infineon TriCore provides an Interrupt System with a high safety standard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps
上传时间： 2013-11-05
上传用户：uuuuuuu
微处理器及微型计算机的发展概况 第一代微处理器是以Intel公司1971年推出的4004，4040为代表的四位微处理机。 第二代微处理机（1973年~1977年），典型代表有：Intel 公司的8080、8085；Motorola公司的M6800以及Zlog公司的Z80。 第三代微处理机 第三代微机是以16位机为代表，基本上是在第二代微机的基础上发展起来的。其中Intel公司的8088。8086是在8085的基础发展起来的；M68000是Motorola公司在M6800 的基础发展起来的； 第四代微处理机 以Intel公司1984年10月推出的80386CPU和1989年4月推出的80486CPU为代表， 第五代微处理机的发展更加迅猛，1993年3月被命名为PENTIUM的微处理机面世，98年PENTIUM 2又被推向市场。 INTEL CPU 发展历史Intel第一块CPU 4004,4位主理器,主频108kHz,运算速度0.06MIPs(Million Instructions Per Second, 每秒百万条指令),集成晶体管2,300个,10微米制造工艺,最大寻址内存640 bytes,生产曰期1971年11月. 8085,8位主理器,主频5M,运算速度0.37MIPs,集成晶体管6,500个,3微米制造工艺,最大寻址内存64KB,生产曰期1976年 8086,16位主理器,主频4.77/8/10MHZ,运算速度0.75MIPs,集成晶体管29,000个,3微米制造工艺,最大寻址内存1MB,生产曰期1978年6月. 80486DX,DX2,DX4,32位主理器,主频25/33/50/66/75/100MHZ,总线频率33/50/66MHZ,运算速度20~60MIPs,集成晶体管1.2M个,1微米制造工艺,168针PGA,最大寻址内存4GB,缓存8/16/32/64KB,生产曰期1989年4月 Celeron一代, 主频266/300MHZ(266/300MHz w/o L2 cache, Covington芯心 (Klamath based),300A/333/366/400/433/466/500/533MHz w/128kB L2 cache, Mendocino核心 (Deschutes-based), 总线频率66MHz,0.25微米制造工艺,生产曰期1998年4月) Pentium 4 (478针),至今分为三种核心:Willamette核心(主频1.5G起,FSB400MHZ,0.18微米制造工艺),Northwood核心(主频1.6G~3.0G,FSB533MHZ,0.13微米制造工艺, 二级缓存512K),Prescott核心(主频2.8G起,FSB800MHZ,0.09微米制造工艺,1M二级缓存,13条全新指令集SSE3),生产曰期2001年7月. 更大的缓存、更高的频率、 超级流水线、分支预测、乱序执行超线程技术 微型计算机组成结构单片机简介单片机即单片机微型计算机，是将计算机主机(CPU、 内存和I/O接口)集成在一小块硅片上的微型机。 三、计算机编程语言的发展概况 机器语言 机器语言就是0，1码语言，是计算机唯一能理解并直接执行的语言。汇编语言 用一些助记符号代替用0，1码描述的某种机器的指令系统，汇编语言就是在此基础上完善起来的。高级语言 BASIC，PASCAL，C语言等等。用高级语言编写的程序称源程序，它们必须通过编译或解释，连接等步骤才能被计算机处理。 面向对象语言 C++，Java等编程语言是面向对象的语言。 1.3 微型计算机中信息的表示及运算基础（一） 十进制ND有十个数码：0～9，逢十进一。 例 1234.5=1×103 +2×102 +3×101 +4×100 +5×10-1加权展开式以10称为基数，各位系数为0～9，10i为权。 一般表达式：ND= dn-1×10n-1+dn-2×10n-2 +…+d0×100 +d-1×10-1+… （二） 二进制NB两个数码：0、1, 逢二进一。 例 1101.101=1×23+1×22+0×21+1×20+1×2-1+1×2-3 加权展开式以2为基数，各位系数为0、1， 2i为权。 一般表达式： NB = bn-1×2n-1 + bn-2×2n-2 +…+b0×20 +b-1×2-1+… （三）十六进制NH十六个数码0～9、A～F，逢十六进一。 例：DFC.8=13×162 +15×161 +12×160 +8×16-1 展开式以十六为基数，各位系数为0～9，A～F，16i为权。 一般表达式： NH= hn-1×16n-1+ hn-2×16n-2+…+ h0×160+ h-1×16-1+… 二、不同进位计数制之间的转换 （二）二进制与十六进制数之间的转换 24=16 ，四位二进制数对应一位十六进制数。举例：（三）十进制数转换成二、十六进制数整数、小数分别转换 1.整数转换法“除基取余”：十进制整数不断除以转换进制基数，直至商为0。每除一次取一个余数，从低位排向高位。举例： 2. 小数转换法“乘基取整”：用转换进制的基数乘以小数部分，直至小数为0或达到转换精度要求的位数。每乘一次取一次整数，从最高位排到最低位。举例： 三、带符号数的表示方法 机器数：机器中数的表示形式。真值： 机器数所代表的实际数值。举例:一个8位机器数与它的真值对应关系如下： 真值： X1=+84=+1010100B X2=-84= -1010100B 机器数：[X1]机= 01010100 [X2]机= 11010100(二)原码、反码、补码最高位为符号位，0表示 “+”，1表示“－”。 数值位与真值数值位相同。 例 8位原码机器数： 真值： x1 = +1010100B x2 =－ 1010100B 机器数： [x1]原 = 01010100 [x2]原 = 11010100原码表示简单直观,但0的表示不唯一，加减运算复杂。 正数的反码与原码表示相同。 负数反码符号位为 1，数值位为原码数值各位取反。 例 8位反码机器数： x= +4： [x]原= 00000100 [x]反= 00000100 x= -4： [x]原= 10000100 [x]反= 111110113、补码（Two’s Complement）正数的补码表示与原码相同。 负数补码等于2n－abs（x）8位机器数表示的真值四、 二进制编码例：求十进制数876的BCD码 876= 1000 0111 0110 BCD 876= 36CH = 1101101100B 2、字符编码 美国标准信息交换码ASCII码，用于计算 机与计算机、计算机与外设之间传递信息。 3、汉字编码 “国家标准信息交换用汉字编码”（GB2312-80标准），简称国标码。 用两个七位二进制数编码表示一个汉字 例如“巧”字的代码是39H、41H汉字内码例如“巧”字的代码是0B9H、0C1H1·4 运算基础 一、二进制数的运算加法规则：“逢2进1” 减法规则：“借1当2” 乘法规则：“逢0出0，全1出1”二、二—十进制数的加、减运算 BCD数的运算规则 循十进制数的运算规则“逢10进1”。但计算机在进行这种运算时会出现潜在的错误。为了解决BCD数的运算问题，采取调整运算结果的措施：即“加六修正”和“减六修正”例：10001000(BCD)+01101001(BCD) =000101010111(BCD) 1 0 0 0 1 0 0 0 ＋ 0 1 1 0 1 0 0 1 1 1 1 1 0 0 0 1 ＋ 0 1 1 0 0 1 1 0 ……调整 1 0 1 0 1 0 1 1 1 进位 例： 10001000(BCD)－ 01101001(BCD)= 00011001(BCD) 1 0 0 0 1 0 0 0 － 0 1 1 0 1 0 0 1 0 0 0 1 1 1 1 1 － 0 1 1 0 ……调整 0 0 0 1 1 0 0 1 三、 带符号二进制数的运算 1.5 几个重要的数字逻辑电路编码器译码器计数器微机自动工作的条件程序指令顺序存放自动跟踪指令执行1.6 微机基本结构微机结构各部分组成连接方式1、以CPU为中心的双总线结构；2、以内存为中心的双总线结构；3、单总线结构CPU结构管脚特点 1、多功能；2、分时复用内部结构 1、控制; 2、运算; 3、寄存器; 4、地址程序计数器堆栈定义 1、定义；2、管理；3、堆栈形式
上传时间： 2013-10-17
上传用户：erkuizhang
