Addfilter is a command-line application which adds and removes filter drivers for a given drive or volume. It is intended to demonstrate how to insert a filter driver into the driver stack of a device. The sample illustrates how to do this by using the SetupDi APIs. The sample works on the x86 platform. It has only been tested in a 32-bit environment. Since Addfilter is not a driver, it does not deal with Plug and Play or Power Management. No INF file is needed to install this application.
标签： command-line application Addfilter drivers
上传时间： 2016-06-28
上传用户：源码3
It includes information about book titles in the library, information about library members, about the number of times the books were read by members, about the suppliers who supply books to the library, and about orders placed with the suppliers
标签： about information library includes
上传时间： 2014-12-22
上传用户：liansi
用AVR单片机设计的MP3播放器 功能： MP3 Player IDE ATA interface FAT 32 with long file name support USB interface On board power supply (input from 7v to 20v DC) Bootloader firmware upgradeable via USB port Infrared bi-directional interface Remote Control Back light graphic LCD worked with only 2x AA batteries In sleep mode sink less than 1uA (2.5mA in active mode) 5 buttons for easy navigation Long range (more than 20 feets)
标签： MP3 interface support Player
上传时间： 2016-07-02
上传用户：fandeshun
Advanced SQL For this exercise, we will use the library schema. It includes information about book titles in the library, information about library members, about the number of times the books were read by members, about the suppliers who supply books to the library, and about orders placed with the suppliers. To distinguish the table names used in this exercise from the table names in other exercise, each table name in this exercise ends with the character 4 .
标签： information Advanced exercise includes
上传时间： 2013-12-20
上传用户：s363994250
Accurate estimates of the autocorrelation or power spectrum can be obtained with a parametric model (AR, MA or ARMA). With automatic inference, not only the model parameters but also the model structure are determined from the data. It is assumed that the ARMASA toolbox is presen
标签： autocorrelation parametric estimates Accurate
上传时间： 2013-12-29
上传用户：3到15
An optimal neuron evolution algorithm for the restoration of linearly distorted images is presented in this paper. The proposed algorithm is motivated by the symmetric positive-definite quadratic programming structure inherent in restoration. Theoretical analysis and experimental results show that the algorithm not only significantly increases the convergence rate of processing, hut also produces good restoration results. In addition, the algorithm provides a genuine parallel processing structure which ensures computationally feasible spatial domain image restoration
标签： restoration evolution algorithm distorted
上传时间： 2013-12-21
上传用户：yy541071797
300 km 传输线和功率补偿仿真 The circuit below represents an equivalent power system feeding a 300 km transmission line. The line is compensated by a shunt inductor at its receiving end. A circuit breaker allows energizing and de-energizing of the line. To simplify matters, only one of the three phases is represented. The parameters shown in the figure are typical of a 735 kV power system.
标签： equivalent represents 300 transmis
上传时间： 2016-07-14
上传用户：15736969615
电力系统向量和连续暂态分析实例This circuit is a simplified model of a 60 Hz, 230 kV three-phase power system where only one phase is represented.
标签： three-phase simplified circuit system
上传时间： 2013-12-14
上传用户：ayfeixiao
SOPC实验--自定义PWM组件:以带一个Avalon Slave 接口的PWM 组件为例，说明如何自定义组件。，一个Avalon Slave 接口可以有clk、chipselect、address、read、readdata、write 及writedata 等信号，但这些信号都不是必需的。 一、功能 我们要实现的PWM 组件具有以下功能： 1． PWM 的周期可改，用period 寄存器存储； 2． PWM 的占空比可改，用duty 寄存器存储。 二、Avalon Slave 接口信号的设计 1．Clk：为PWM 提供时钟； 2．Write：写信号，可以通过Avalon Slave 总线将period 和duty 值从Nios II 应用程序 传送到组件逻辑中。 3．Writedata：写数据。通过此数据线传送period 和duty 值。 4．Address：本例中有两个寄存器，因此可用一根地址线表示。 5．全局信号。本例中PWM 的输出用来驱动LED 灯显示，这个信号不属于Avalon 接 口信号。
上传时间： 2013-12-28
上传用户：bibirnovis
为LINUX设计一个简单的二级文件系统。要求做到以下几点： 1、 可以实现下列几条命令 Login 用户登录 Dir 列文件目录 Create 创建文件 Delete 删除文件 Open 打开文件 Close 关闭文件 Read 读文件 Write 写文件 2、列目录时要列出文件名、物理地址、保护码和文件长度。 3、源文件可以进行读写保护。
上传时间： 2016-07-16
上传用户：jeffery
