BGA布线指南 BGA CHIP PLACEMENT AND ROUTING RULE BGA是PCB上常用的组件，通常CPU、NORTH BRIDGE、SOUTH BRIDGE、AGP CHIP、CARD BUS CHIP…等，大多是以bga的型式包装，简言之，80﹪的高频信号及特殊信号将会由这类型的package内拉出。因此，如何处理BGA package的走线，对重要信号会有很大的影响。 通常环绕在BGA附近的小零件，依重要性为优先级可分为几类： 1. by pass。 2. clock终端RC电路。 3. damping（以串接电阻、排组型式出现；例如memory BUS信号） 4. EMI RC电路（以dampin、C、pull height型式出现；例如USB信号）。 5. 其它特殊电路（依不同的CHIP所加的特殊电路；例如CPU的感温电路）。 6. 40mil以下小电源电路组（以C、L、R等型式出现；此种电路常出现在AGP CHIP or含AGP功能之CHIP附近，透过R、L分隔出不同的电源组）。 7. pull low R、C。 8. 一般小电路组（以R、C、Q、U等型式出现；无走线要求）。 9. pull height R、RP。 中文DOC，共5页，图文并茂
上传时间： 2013-04-24
上传用户：cxy9698
·详细说明：外挂硬盘和FLASH的MP3播放器解决方案，用C和汇编编写，并附带有电路原理图- Outside hangs the hard disk and the FLASH MP3 player solution, with C and the assembly compilation, and has the electric circuit schematic diagram in pass
上传时间： 2013-06-12
上传用户：yangbo69
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
针对盘山路存在的转弯盲区，即在转弯时司机无法得知弯路对面是否有车辆通过，设计一种基于C8051F310的山路转弯预防警示系统。该系统利用一阶滤波算法检测山路转弯时是否有车辆通过。运用该算法可增强系统检测的实时性，提高检测机动车辆的灵敏度，同时大大减少环境温度对检测的干扰。试验表明该系统能够正确指示出在山路转弯时是否有车辆通过，目前该系统已安装在盘山路上，可大大减少事故的发生率。 Abstract: Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
上传时间： 2013-10-10
上传用户：归海惜雪
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
摘 要:用一种新的思路和方法,先计算低通、再计算高通滤波器的有关参数,然后组合成带通滤波器.关键词:滤波器;参数;新思路中图分类号: TN713. 5 文献识别码:B 文章编号:1008 - 1666 (1999) 04 - 0089 - 03A New Consideration of the Band Filter’s CalculationGuo Wencheng( S hao Yang B usiness and Technology school , S haoyang , Hunan ,422000 )Abstract :This essay deals with a new method of calculating the band filters - first calculatingthe relevant parameters of low - pass filters ,then calculating the ones of high - pass filters.Key words :filter ; parameters ;new considercation八十年代后,信息产业得到了迅猛发展. 带通滤波器在微波通信、广播电视和精密仪器设备中得到了广泛应用. 带通滤波器性能的优劣,对提高接收机信噪比,防止邻近信道干扰,提高设备的技术指标,有着十分重要的意义.我在长期的教学实践中,用切比雪夫型方法设计、计算出宽带滤波器集中参数元件的数据. 该滤波器可运用在检测微波频率的仪器和其他设备中. 再将其思路和计算方法介绍给大家,供参考.
上传时间： 2014-12-28
上传用户：Yukiseop
针对使用硬件描述语言进行设计存在的问题，提出一种基于FPGA并采用DSP Builder作为设计工具的数字信号处理器设计方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ设计流程，设计了一个12阶FIR 低通数字滤波器，通过Quartus 时序仿真及嵌入式逻辑分析仪SignalTapⅡ硬件测试对设计进行了验证。结果表明，所设计的FIR 滤波器功能正确，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as designed tool is pointed out.A 12-order low-pass FIR digital filter was designed according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the designed filter is correct in function and good in performance.
上传时间： 2013-11-17
上传用户：lo25643
The high defi nition multimedia interface (HDMI) is fastbecoming the de facto standard for passing digitalaudio and video data in home entertainment systems.This standard includes an I2C type bus called a displaydata channel (DDC) that is used to pass extended digitalinterface data (EDID) from the sinkdevice (such as adigital TV) to the source device (such as a digital A/Vreceiver). EDID includes vital information on the digitaldata formats that the sink device can accept. The HDMIspecifi cation requires that devices have less than 50pFof input capacitance on their DDC bus lines, which canbe very diffi cult to meet. The LTC®4300A’s capacitancebuffering feature allows devices to pass the HDMI DDCinput capacitance compliance test with ease.
上传时间： 2013-11-21
上传用户：tian126vip
基于通用集成运算放大器，利用MASON公式设计了一个多功能二阶通用滤波器，能同时或分别实现低通、高通和带通滤波，也能设计成一个正交振荡器。电路的极点频率和品质因数能够独立、精确地调节。电路使用4个集成运放、2个电容和11个电阻，所有集成运放的反相端虚地。利用计算机仿真电路的通用滤波功能、极点频率和品质因数的独立控制和正交正弦振荡，从而证明该滤波器正确有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
上传时间： 2013-10-09
上传用户：13788529953
