PCI是一种高性能的局部总线规范，可实现各种功能标准的PCI总线卡。本文简要介绍了PCI总线的特点、信号与命令，提出了一种利用高速FPGA实现PCI总线接口的设计方案。\r\n
上传时间： 2013-08-30
上传用户：brain kung
基于FPGA的PCI总线接口的设计方案\r\n~！
上传时间： 2013-09-01
上传用户：heart520beat
2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.
上传时间： 2013-10-07
上传用户：ysystc670
PCI ExpressTM Architecture Add-in Card Compliance Checklist for the PCI Express Base 1.0a SpecificationThe PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.Contact the PCI Special Interest Group office to obtain the latest revision of this checklistQuestions regarding the ths document or membership in the PCI Special Interest Group may be forwarded tPCI Special Interest Group5440 SW Westgate Drive #217Portland, OR 97221Phone: 503-291-2569Fax: 503-297-1090 DISCLAIMERThis document is provided "as is" with no warranties whatsoever, including any warranty of merchantability, noninfringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification, or sample. The PCI SIG disclaims all liability for infringement of proprietary rights, relating to use of information in this specification. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted herein.
标签： Architecture ExpressTM PCI
上传时间： 2013-11-03
上传用户：gy592333
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
PCI ExpressTM is the third generation of PCI (PeripheralComponent Interconnect) technology used to connect I/Operhipheral devices in computer systems. It is intended asa general purpose I/O device interconnect that meets theneeds of a wide variety of computing platforms such asdesktop, mobile, server and communications. It alsospecifies the electrical and mechanical attributes of thebackplane, connectors and removable cards in thesesystems.
上传时间： 2013-11-17
上传用户：squershop
在深入分析了意法半导体公司推出的STM32、高速PCI总线以及运动控制卡的功能和结构特点的基础上，设计了一款可直接插在PCI 插槽中的伺服运动控制卡。不仅可大大降低了成本，更为开放式数控系统的研究提供了一个全新的思路。结果表明，本文所设计的伺服控制卡满足了目前控制系统的性能和要求。
上传时间： 2014-12-25
上传用户：l银幕海
PSHLY-B回路电阻测试仪介绍
上传时间： 2013-11-05
上传用户：木子叶1
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
详细介绍了PCI9052接口器件的功能、结构和使用方法，并结合实际给出了基于PCI9052器件开发PCI总线接口卡的应用实例。 Abstract: The main functions,structures and usage of PCI9052inferface chip are introduced in detail in this paper.And an application example of designing PCI bus interface card based on PCI9052is proposed in this paper.
上传时间： 2013-10-16
上传用户：togetsomething
