对读入的某个文本文件input.txt中，拆出英文单词，输出一个按字典顺序排列的单词表，结果输出在文本文件output.txt中，每个单词一行，并在单词后输出该单词出现的个数，两个字段之间用逗号分隔。约定单词仅由英文字母组成，单词间由非英文字母分隔，相同单词只输出一个，大小写不区分。 利用二叉树实现
上传时间： 2015-07-04
上传用户：yulg
vc下基于对话框的h。263文件解码并显示。263文件在目录下，为output。263，共90祯，解码后显示（176*144格式）。
上传时间： 2015-07-09
上传用户：yzy6007
h.263 c编码源码。目录下有input。qcif原始未压缩文件，运行程序生成重建文件recon。qcif和压缩后文件output。263文件。
上传时间： 2013-12-19
上传用户：ljmwh2000
This mfile illustrates a simple two path Rayleigh multipath fading channel This mfile inputs an unmodulated sinewave through a simple Rayleigh two path fading channel and shows the output with phase, gain, and attenuation characteristics via animation
标签： mfile This illustrates multipath
上传时间： 2014-08-30
上传用户：lindor
加密算法 Test Driver for Crypto++, a C++ Class Library of Cryptographic Primitives: - To generate an RSA key cryptest g - To encrypt and decrypt a string using RSA cryptest r - To calculate MD5, SHS, and RIPEMD-160 message digests: cryptest m file - To encrypt and decrypt a string using DES-EDE in CBC mode: cryptest t - To encrypt or decrypt a file cryptest e|d input output - To share a file into shadows: cryptest s <pieces> <pieces-needed> file (make sure file has no extension, if you re running this under DOS) - To reconstruct a file from shadows: cryptest j output file1 file2 [....] - To gzip a file: cryptest z <compression-level> input output - To gunzip a file: cryptest u input output - To run validation tests: cryptest v - To run benchmarks: cryptest b [time for each benchmark in seconds]
标签： Cryptographic Primitives generate Library
上传时间： 2015-07-16
上传用户：wqxstar
solve the 8-puzzle problem using A* algorithm. Definitely written by my self, also include BGI graphics library output.
标签： Definitely algorithm problem include
上传时间： 2014-01-17
上传用户：zm7516678
工程计算MATLAB code to calculate the reorthogonalized sine tapers input: N = the length of the time series data to be tapered p = the number of tapers requested I = the gap structure a vector of length N I(t) = 1 if there is data at time t, t=1, ..., N I(t) = 0 if there is a gap at time t output: X = N-by-p vector of the reorthogonalized sine taper
标签： the reorthogonalized calculate MATLAB
上传时间： 2013-12-17
上传用户：wangyi39
his project was built and tested with WinAVR-20060125. Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!! To build the code, just install WinAVR and run "make" from the console in echomaster and echoslave subdirs. "make program" will program the device if you have a AVRISP attached. Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST! Otherwise you wont get any clock signal to the AVR and then you can t program it or reset the fuses! The MC1319x has default clock output of 32kHz so you will have to set your programmer to a very low frequency (<=32kHz/4) to be able to program it while it is running on that!
标签： the 20060125 project WinAVR
上传时间： 2014-10-10
上传用户：yan2267246
Test program to loop on Successive Approximation A-to-D conversion. Allows digital codes and resulting DAC output to be viewed on scope.
标签： Approximation Successive conversion program
上传时间： 2015-08-07
上传用户：顶得柱
1. 用SYSDBA登录服务器，并且创建一个MISDBA用户，密码为PASSWORD。 2. 用SYSDBA用户创建MISDB数据库（可直接注册使用光盘提供的MISDB.GDB）。 3. 用MISDBA用户登录MISDB数据库。 4. 在ISQL中，依次输入第5章的数据表创建SQL语句；或者根据表5-1至表5-7自行创建数据表。 5. 在SQL Explorer中创建MISDB数据库连接。 6. 用MISDBA用户登录，并且输入原始数据。除了表5-8至表5-11的内容，还需要根据需要设置部门（DEPARTMENT）、职务（JOB）和人事科登录用户（ID=’RSK’，PASSWD=’RSK’，AUTHORITY=’3’，STATE=’F’）。 7. 修改源程序中的数据库连接组件参数。
上传时间： 2013-12-16
上传用户：缥缈
