紧凑型荧光灯（CFL）作为绿色照明产品已得到国家的认可与大力推荐。为充分发挥CFL调光灯的特点，恩智浦半导体推出了UBA2028用于CFL调光灯的控制芯片。它是采用EZ-HV SOI工艺流程做的600V的集成芯片，内部集成半桥驱动电路和两个MOSFET管；UBA2028其支持的工作电流在不超过芯片最高温度1500C限制下可以达到700mA；由于它集成度高，外接元件显著减少,可以构成一个高效率，高可靠的调光节能灯控制系统；性价比非常好。
上传时间： 2013-10-28
上传用户：hgy9473
根据滑差电机电磁调速器的技术特点,提出一种由PIC16F877单片机组成控制单元的电磁调速器控制系统。系统采用转速按键预置、LCD实时显示;以不控整流代替相控整流,选用MOSFET构成PWM控制主回路,输出电压稳定、输出电流连续,具有快速的动态响应;用光电传感器测速电路代替测速发电机,电路简洁,效率高、能耗低。实验表明电路的性能良好,可靠性高,成本低。
上传时间： 2013-10-20
上传用户：gtzj
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
上传时间： 2014-12-04
上传用户：axin881314
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
IntroductionAs chip designers pack more functions into ICs,pin counts continue to grow and the space betweenpins keeps shrinking. Pin spacings of 0.5 mm and0.65 mm are not at all uncommon. The power ofthese new ICs is wonderful, to be sure, but trou-bleshooting them can be a chore because connect-ing scopes and logic analyzers has become muchmore difficult and less dependable.
标签： Agilent Probing Wedge High
上传时间： 2013-10-22
上传用户：蒋清华嗯
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-15
上传用户：zouxinwang
Features• Complete DTMF Receiver• Low power consumption• Internal gain setting amplifier• Adjustable guard time• Central office quality• Power-down mode• Inhibit mode• Backward compatible withMT8870C/MT8870C-1Applications• Receiver system for British Telecom (BT) orCEPT Spec (MT8870D-1)• Paging systems• Repeater systems/mobile radio• Credit card systems• Remote control• Personal computers• Telephone answering machine
上传时间： 2013-11-20
上传用户：mpquest
LLCR Pin Socket Testing with the Model 3732 High Density Matrix Card Computer processors (CPUs) today have come a long way from the computer processors of the past. They draw more power, run at lower voltages, and have more pins than ever before.
上传时间： 2013-10-24
上传用户：whenfly
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
