介绍了以AVR单片机ATmega16为核心，采用前端信号调理电路、程控增益放大器以及波形显示LCD（GDM12864A）实现的一个简易示波器。并给出该系统设计的硬件和软件设计方案。 Abstract: Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR microcontroller ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,gain-programmed amplifier circuit and LCD’s interface circuit and so on.
上传时间： 2013-10-13
上传用户：ccccccc
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
介绍一种基于C8051F060单片机和NAND Flash的数据采集存储系统，该系统可实现3路信号采样，每路采样率为5KS/s,通过异步串行通信接口实现数据传输。并详细说明系统的软件设计。 Abstract: An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
上传时间： 2013-10-12
上传用户：Jesse_嘉伟
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号，并经放大电路处理后送入C8051F020单片机，再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化，然后分别对数据进行存储和显示。该测量仪能测量6路压力信号，并且各测量点都能单独检测和设置。由于采用了C8051F020单片机，简化了硬件电路，增强了抗干扰能力，使得测量仪具有测量精度高，冲击小等特点。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上传时间： 2013-11-16
上传用户：yare
MMC/SD卡以其优越的性能，在单片机嵌入式设备中得到广泛应用。将MMC/SD卡作为外部掉电存储介质应用于音频信号发生器中，通过8051F330单片机上的SPI接口，实现单片机—MMC/SD卡的存储扩展，设计了此硬件平台上的MMC/SD卡的单片机驱动程序，并给出了相应的程序代码，满足音频信号发生器的大容量存储要求。 Abstract: MMC/SD card is more and more widely used in the single chip embedded devices for their excellent performances.This article introduces the application of MMC/SD card as the external power down storage medium in audio signal generator. The extension technology especially for storage of single chip-MMC/SD card via SPI interfaces in 8051F330 single chip, including designs single chip drive program of MMC/SD card based on hardware platform,and also gives the key coding of the program. The implementation of big capacity storage is meaningful in audio signal generator.
上传时间： 2014-12-27
上传用户：黄华强
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
介绍了基于单片机航空交流电参数测试仪的系统设计。以Silicon Labs公司的C8051F005单片机为核心设计出数据采集板，通过RS-232串口与上位机通讯。运用Lab Windows/CVI编写的上位机软件实现信号的检测以及波形和数据的显示，给出了测试仪硬件电路的组成和软件流程图。本系统具有硬件结构简单、容易实现和成本低等特点，在实际应用中其稳定性、精确性均能满足客户要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
上传时间： 2013-11-18
上传用户：wang5829
介绍了基于单片机C8051F020的通用串口适配器的设计与实现方法，即由单片机控制的智能化一对多口收发信号转换器。通过采用C51对单片机进行编程，控制与RS-232（标准RS-232电平）、RS232(TTL电平)、RS-422接口的数据通信；采用C++ Builder作为开发平台，通过RS-232接口实现上位机对适配器各个通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
上传时间： 2013-11-19
上传用户：hebanlian
