机电类比法是一种把机械量通过一定的计算等效类比为电量的方法，其在对电子机械系统的分析中应用非常广泛。它能够把一个较复杂的机械系统类比为我们熟知的电路系统来进行分析，从而使问题的分析得到简化。本文通过对振弦式传感器的分析介绍了机电类比法，并对使用电路进行了相关的分析。 Summary：The electromechanical analogy is assort of analysis which is to analogize the mechanical system by using circuit system , it applied widely in the filed of analysis the electronic-mechanical system. The analysis can take a complex mechanical system analogous to a circuitry that we well-known, which can simplify the problems. In the paper, the electro-mechanical analogy method is briefly introduced by analysis the vibrating wire sensor，and have a correlation analysis about the circuit we used.关键词： 机电类比法 振弦式传感器 频率 振荡 反馈Keyword：electro-mechanical analogy method，vibrating wire sensor，frequency, oscillation, feedback 0 引言振弦式传感器是属于频率式传感器的一种。所谓频率式传感器就是能直接将被测量转换为振动频率信号的传感器，这类传感器一般是通过测量振弦、振筒、振梁、振膜等弹性振体或石英晶体谐振器的固有谐振频率来达到测量引起谐振频率变化的被测非电量的目的，其也称为谐振式传感器[1]。在分析该类传感器中，由于其涉及到频率，就容易让人联想到在电子技术中接触到的RLC振荡电路。因此可以尝试着用类比的方法使之对应起来分析,即机电类比法分析。
上传时间： 2013-11-16
上传用户：paladin
首先提出了基于PM(propagator method)方法的波达方向(DOA)、频率联合估计快速算法，给出了PM 算子的一个估计，由PM 算子构造出一特殊的低维矩阵，其特征值给出频率的估计，进而由估计的频率和相应的特征矢量得到DOA 的估计。
上传时间： 2014-09-12
上传用户：xauthu
阐述了轨道交通列车定位技术。介绍了在轨道交通系统中列车定位技术的功能，国内外轨道交通中主要采用的列车定位方法，重点论述了几种主要定位技术，并从定位精度、闭塞制式、维护投资成本、抗干扰等方面进行分析比较。提出目前轨道交通定位技术应综合运用，取长补短，多种方法相互融合，才能满足轨道交通中对安全可靠性的要求。 Abstract: Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintenance and investment cost， interference and so on， suggested that the current rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requirements of rail safety.
上传时间： 2013-11-25
上传用户：franktu
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
本软件是关于MAX338, MAX339的英文数据手册：MAX338, MAX339 8通道/双4通道、低泄漏、CMOS模拟多路复用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上传时间： 2013-11-12
上传用户：18711024007
This application note describes how to retrieve user-defined data from Xilinx configurationPROMs (XC18V00 and Platform Flash devices) after the same PROM has configured theFPGA. The method to add user-defined data to the configuration PROM file is also discussed.The reference design described in this application note can be used in any of the followingXilinx FPGA architectures: Spartan™-II, Spartan-IIE, Spartan-3, Virtex™, Virtex-E, Virtex-II,and Virtex-II Pro.
上传时间： 2013-10-09
上传用户：guojin_0704
The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Specification Revision 2.0a ([Ref 6]) dictates that when a target signals adata transfer, "the target must do so within 16 clocks of the assertion of FRAME#." PCItermination transactions, such as Split Response/Complete, are commonly used to meet thelatency specifications. This method adds complexity to the design, as well as additional systemlatency. Another solution is to increase the ratio of the memory frequency to the PCI-X busfrequency. However, this solution increases the required power and clock resource usage.
上传时间： 2013-11-24
上传用户：18707733937
针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言编写出源程序，在Virtex-II Pro 开发板上成功实现了整个系统。测试结果表明该系统正确实现了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上传时间： 2013-11-19
上传用户：neu_liyan
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2013-10-10
上传用户：zxc23456789
本文利用Verilog HDL 语言自顶向下的设计方法设计多功能数字钟，突出了其作为硬件描述语言的良好的可读性、可移植性和易理解等优点，并通过Altera QuartusⅡ 4.1 和ModelSim SE 6.0 完成综合、仿真。此程序通过下载到FPGA 芯片后，可应用于实际的数字钟显示中。 关键词：Verilog HDL；硬件描述语言；FPGA Abstract: In this paper, the process of designing multifunctional digital clock by the Verilog HDL top-down design method is presented, which has shown the readability, portability and easily understanding of Verilog HDL as a hard description language. Circuit synthesis and simulation are performed by Altera QuartusⅡ 4.1 and ModelSim SE 6.0. The program can be used in the truly digital clock display by downloading to the FPGA chip. Keywords: Verilog HDL；hardware description language；FPGA
上传时间： 2013-11-10
上传用户：hz07104032
