标号： ＦＤＩＶ 功能：浮点数除法 入口条件：被除数在[R0]中，除数在[R1]中。出口信息：OV=0时，商仍在[R0]中，OV=1时，溢出。影响资源：PSW、A、B、R2～R7、位1EH、1FH 堆栈需求： ５字节
上传时间： 2014-12-28
上传用户：wfl_yy
入口条件：被除数在R2、R3、R4、R5中，除数在R6、R7中。出口信息：OV=0时商在R2、R3中，OV=1时溢出。影响资源：PSW、A、B、R1～R7 堆栈需求： ５字节DIVS: LCALL MDS ；计算结果的符号和两个操作数的绝对值PUSH PSW ；保存结果的符号LCALL DIVD ；计算两个绝对值的商JNB OV,DVS1 ；溢出否？POP ACC ；溢出，放去结果的符号，保留溢出标志
上传时间： 2013-11-09
上传用户：lht618
介绍了基于51单片机的网络连接控制器的软硬件设计方案，主要采用Atmel公司的8 b单片机AT89C51作为核心处理器，采用RealTek公司的RTL8O19AS芯片接入以太网。同时讨论了精简的TCP／IP协议栈的分层次实现，实现了可靠的UDP数据通信。
上传时间： 2013-11-22
上传用户：alex wang
The PCA9540B is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register.
上传时间： 2014-12-28
上传用户：nshark
The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register. Two interrupt inputs, INT0 and INT1, one for each of theSCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as anAND of the two interrupt inputs, is provided.
上传时间： 2013-12-07
上传用户：europa_lin
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
1. 文件比较器TKSDiff ：a) 二进制比较：支持字体设置和文件改动监测，微调智能比较算法b) 支持文件拖拽，内容替换和插入c) 支持复制选中文本和比较文件的文件名d) 支持选中内容的导出e) 显示智能比较完成度f) 处理k-flash命令行g) 禁止大文件间的比较h) 修正部分内存越界问题i) 修正消除二进制标题时有时无问题j) 修正目录比较界面模块资源泄漏问题k) 修正快速比较设置起始地址 bug
上传时间： 2013-10-13
上传用户：CSUSheep
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
